manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 733

 

15-107

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Pre-Manual Switchover Switch Integrity Diagnostic Utility

Operating

There are three new CLI commands related to the BTS 10200 Tabular Display of Events and Alarms 
feature correlating to the following:

  •

Show current alarms in tabular format

  •

Show alarms history in tabular format

  •

Show events history in tabular format

CLI Commands

The following are CLI commands and there description:

  •

show tab-alarm

—Shows current alarms in tabular format

  •

show tab-alarm-hist

—Shows alarms history in tabular format

  •

show tab-event-hist

—Shows events history in tabular format

An example of the output of executing of one the three commands follows:

CLI>s

how tab-alarm

Pre-Manual Switchover Switch Integrity Diagnostic Utility

This section describes the Pre-Manual Switchover Switch Integrity Diagnostic Utility feature that 
provides the switchover target system health information. For costly traffic outages to be avoided, the 
switchover decision must be made based on the system health information. The diagnostic script utility 
automates the manual procedures that are used to collect, check, and verify system health information.

The Cisco BTS 10200 Softswitch Pre-Manual Switchover Switch Integrity Diagnostic Utility feature 
provides the system health information of the switchover target so that Cisco BTS 10200 Softswitch 
customers can decide if they want to perform manual switchover.

The customer service provider operation organizations often periodically perform switchovers during 
maintenance windows (after midnight and early in the morning). Doing so ensures that the mate system 
is functional and cleans up any abnormalities that might have accumulated in the current active/primary 
system (e.g., memory leaks, hung processes).

In order to facilitate the switchover operational practice, the Cisco BTS 10200 Softswitch Pre-Manual 
Switchover Switch Integrity Diagnostic Utility feature provides a diagnostic tool/utility that allows the 
operator to verify the operational status of the standby system/platform and decide whether it is in a 
ready state for a switchover.

Note

See the 

Cisco BTS 10200 Softswitch Network and Subscriber Feature Descriptions

 guide for a complete 

list of subscriber features supported by the Cisco BTS 10200 Softswitch.

ID

TYPE

NUMBER

SEVERITY

TIMESTAMP

COMPONENT-ID

12331874656

SIGNALING

68

MAJOR

2005-11-20 11:00:00

testing@mgw_id

12331874657

MAINTENANCE

3

MAJOR

2005-11-20 11:01:00

testing

12331874658

OSS

9

MINOR

2005-11-20 11:02:45

unixserver

12331874659

OSS

9

MINOR

2005-11-20 11:02:45

skittles

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands