manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 664

 

15-38

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Query Verification Tool and Translation Verification Tool

Example 4

This example is for a QOR originating switch. A subscriber dials a DN that is ported-out of another 
(donor) switch. The call is translated and routed to the donor switch

, 

as shown in the first translate 

TVT

 

command below. The donor switch sends a REL with LNP QOR: Ported Number cause to the originating 
switch.

The originating switch receives the REL with LNP QOR: Ported Number cause, and then the originating 
switch does an LNP query. The QVT query finds an RN, and the RN and NOA are used as input to the 
TVT to show the routing after the QOR query, as shown in the second translated command below.

btsadmin>translate line calling-dn=11501511; called-dn=11161168

TRANSLATE ON CALL AGENT CA146 IS... -> 

TABLEINFO -> 

TABLE: SUBSCRIBER

ID=sipata1;CATEGORY=INDIVIDUAL;NAME=h15 sipata1 

Moe;STATUS=ACTIVE;BILLING_DN=11501511;DN1=11501511;PRIVACY=NONE;RING_TYPE_DN1=1;PIC1=NONE;

PIC2=NONE;PIC3=NONE;GRP=N;USAGE_SENS=Y;SUB_PROFILE_ID=hungary_prof;TERM_TYPE=SIP;IMMEDIATE

_RELEASE=N;TERMINATING_IMMEDIATE_REL=N;[email protected];SEND_BDN_AS_CPN=N;SE

ND_BDN_FOR_EMG=N;PORTED_IN=N;BILLING_TYPE=NONE;VMWI=Y;SDT_MWI=Y;

TABLE: SUBSCRIBER_PROFILE

ID=hungary_prof;DIAL_PLAN_ID=dp_sub_itu;LOCAL_PFX1_OPT=NR;TOLL_PFX1_OPT=RQ;POP_ID=hun1;OLI

=0;EA_USE_PIC1=Y;INTERLATA_PFX1_OPT=RQ;

     .

     .

     .

TABLE: TRUNK_GRP

ID=6;CALL_AGENT_ID=CA146;TG_TYPE=SS7;NUM_OF_TRUNKS=24;DPC=5-2-4;TG_PROFILE_ID=tgprof_inet1

16;STATUS=INS;DIRECTION=OUT;SEL_POLICY=DSC;GLARE=SLAVE;ALT_ROUTE_ON_CONG=N;SIGNAL_PORTED_N

UMBER=Y;POP_ID=hun1;DIAL_PLAN_ID=dp_trk_itu;DESCRIPTION=TG OUT to Inet 

116;DEL_DIGITS=0;TRAFFIC_TYPE=LOCAL;ANI_BASED_ROUTING=N;CALL_CTRL_ROUTE_ID=cc_rte_i116_tg6

;MGCP_PKG_TYPE=T;ANI_SCREENING=N;SEND_RDN_AS_CPN=N;STATUS_MONITORING=N;SEND_EARLY_BKWD_MSG

=N;EARLY_BKWD_MSG_TMR=5;SCRIPT_SUPP=N;VOICE_LAYER1_USERINFO=AUTO;VOICE_INFO_TRANSFER_CAP=A

UTO;ACCESS_TYPE=COMBINED;POI=INTER_ENDOFFICE;PERFORM_LNP_QUERY=N;

Reply : Success: 

btsadmin>

btsadmin>

btsadmin>

btsadmin>

btsadmin>query LNP; calling-dn=11501511; called-dn=11161168;

QUERY ON FEATURE SERVER FSAIN205 IS... -> 

RESULT -> 

Called Number=11161168, Routing Number (RN) =4001

**** Suggested TRANSLATE Command ****

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands