manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 632

 

15-6

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 15      Diagnostic Tests

Signaling System 7 Trunk Termination Tests

Signaling System 7 Trunk Termination Tests

This section describes the tests that can be performed on Signaling System 7 (SS7) trunk terminations. 
All terminations must be in the MAINT state for testing.

Step 1

Force the SS7 trunk termination into MAINT state:

control ss7-trunk-termination tgn-id=103; mode=forced; target-state=maint;

Note

Set customer-originated trace (COT), circuit verification message (CVM), and circuit query 
message (CQM) on the terminating gateway or switch to perform these tests. Otherwise, the test 
or tests will fail.

Step 2

Display the Test Menu.

diag ss7-trunk-termination

Reply Example:

Reply: Diagnostic SS7 Trunk Group Menu.

===

Test 1: SS7 MGCP Connectivity Test

Test 2: SS7 Termination Connection Test

Test 3: SS7 COT Test

Test 4: SS7 CQM Test

Test 5: SS7 CVT Test

Test 6: SS7 CIC Audit

Test 0: ALL Tests

Note

Test #1 tests if MGCP has access to the SS7 trunk termination. 

 

Test #2 tests if there is a path to the device (ping). 

 

Test #3 tests the integrity of the SS7 Bearer Path. 

 

Test #4 queries the SS7 circuit (or group of circuits) status. A range of CICs can be specified (to a 
maximum of 24). Both remote and local trunk states are displayed in the results.

 

Test #5 tests to ensure that each end of the circuit has sufficient and consistent information for using the 
circuit in call connections. Common language location identifier (CLLI) names are included.

 

Test #6 tests to ensure the CIC connections.

 

Test #0 performs tests 1 through 6.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands