Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 276

Page: 276 / 874

7-44

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7 Maintenance Troubleshooting

Maintenance Events and Alarms

MAINTENANCE (82)

To troubleshoot and correct the cause of the alarm, refer to the

“Average Outgoing Heartbeat Period

Exceeds Critical Limit—Maintenance (82)” section on page 7-106

MAINTENANCE (83)

To troubleshoot and correct the cause of the alarm, refer to the

“Swap Space Below Minor

Threshold—Maintenance (83)” section on page 7-106

DESCRIPTION

Average Outgoing Heartbeat Period Exceeds Critical Limit (Average Outgoing HB Period Exceeds
Critical Limit)

SEVERITY

CRITICAL

THRESHOLD

100

THROTTLE

DATAWORDS

Critical Threshold F–FOUR_BYTES

Current Average HB Peri–FOUR_BYTES

PRIMARY

CAUSE

The CPU is overloaded.

PRIMARY

ACTION

Shutdown the platform.

DESCRIPTION

Swap Space Below Minor Threshold

SEVERITY

MINOR

THRESHOLD

THROTTLE

DATAWORDS

Minor Threshold (MB)–FOUR_BYTES

Current Value (MB)–FOUR_BYTES

PRIMARY

CAUSE

Too many processes are running.

PRIMARY

ACTION

Stop the proliferation of executables (processes-scripts).

SECONDARY

CAUSE

File spaces /tmp or /var/run are over-used.

SECONDARY

ACTION

Cleanup the file systems.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Search results

Summary of Contents for BTS 10200 Softswitch

Reviews:

Brands by name

Popular brands