manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 263

 

7-31

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 7      Maintenance Troubleshooting

Maintenance Events and Alarms

MAINTENANCE (54)

For additional information, refer to the 

“The Central Processing Unit has Returned to Normal Levels of 

Operation—Maintenance (54)” section on page 7-78

.

MAINTENANCE (55)

To troubleshoot and correct the cause of the alarm, refer to the 

“The Five Minute Load Average is 

Abnormally High—Maintenance (55)” section on page 7-102

.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

DESCRIPTION

The Central Processing Unit has Returned to Normal Levels of Operation (The CPU has Returned to 
Normal Levels of Operation)

SEVERITY

INFO

THRESHOLD

100

THROTTLE

0

DATAWORDS

Host Name–STRING [40]

 

CPU Usage–STRING [40] 

PRIMARY

 

CAUSE

N/A

PRIMARY

 

ACTION

N/A

DESCRIPTION

The Five Minute Load Average is Abnormally High

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Host Name–STRING [40]

 

Load Average–STRING [40] 

PRIMARY

 

CAUSE

Multiple processes are vying for processing time on the system, which is normal in a high traffic 
situation such as heavy call processing or bulk provisioning.

PRIMARY

 

ACTION

Monitor the system to ensure that all subsystems are performing normally. If they are, only lightening 
the effective load on the system will clear the situation. If they are not, verify which process(es) are 
running at abnormally high rates and provide the information to Cisco TAC. (Contact Cisco TAC.)

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands