manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 213

 

6-19

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 6      Database Troubleshooting

Database Events and Alarms

DATABASE (25)

To troubleshoot and correct the cause of the alarm, refer to the 

“Secure File Transfer Protocol Transfer 

Failed—Database (25)” section on page 6-37

.

DATABASE (26)

To troubleshoot and correct the cause of the alarm, refer to the 

“File Write Error—Database (26)” section 

on page 6-37

.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

DESCRIPTION

Secure File Transfer Protocol Transfer Failed (SFTP Transfer Failed)

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

FileName - STRING [128]

 

Error - STRING [50]

PRIMARY

 

CAUSE

Unable to connect between active and standby call agents.

PRIMARY

 

ACTION

Verify communication between primary and CA. On each CA, ping the other node.

SECONDARY

 

CAUSE

Unable to login to remote host.

SECONDARY

 

ACTION

Verify that secure shell (SSH) keys have been pre-configured for user root on both active and standby 
call agents.

TERNARY

 

CAUSE

File transfer error.

TERNARY

 

ACTION

Check the Error dataword to see if it gives an indication of the kind of error that occurred. It could be 
a file-system error on the remote host, or a communication failure between the active and standby call 
agents.

DESCRIPTION

File Write Error

SEVERITY

MAJOR

THRESHOLD

100

THROTTLE

0

DATAWORDS

Path Name - STRING [128]

PRIMARY

 

CAUSE

System error, may be out of file descriptors.

PRIMARY

 

ACTION

Call Cisco TAC technical support. (Contact Cisco TAC.)

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands