manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 142

 

3-36

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 3      Billing Troubleshooting

Troubleshooting Billing Alarms

Billing Partition Disk Usage Critical Threshold Exceeded—Billing (4)

The Billing Partition Disk Usage Critical Threshold Exceeded alarm (critical) indicates that a billing 
partition disk usage critical threshold crossing has occurred. The primary cause of the alarm is that call 
detail records are accumulating on the disk associated with the billing database in the EMS. This is 
because data is being written into the database faster than it is being read out of the database. The major 
threshold (default value = 90%) has been exceeded. Some fluctuation in disk usage is to be expected as 
call volume rises and falls during the day. Threshold crossings might step upward (from MINOR to 
MAJOR to CRITICAL) when there is a rapid increase in call volume, and then step downward 
(CRITICAL to MAJOR to MINOR) when call volume slows. To correct the primary cause of the alarm, 
Monitor this alarm. The read should catch up to write within a few minutes, and the alarm should not 
remain active. To monitor the alarm, use the 

subscribe alarm-report

 command. To obtain a summary, 

use the 

report alarm-summary

 command. Verify that type = billing is entered in these commands. If 

the alarm does not clear (or step down to a reduced level) in a few minutes, contact Cisco TAC for 
assistance.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

Prior to contacting Cisco TAC, from the UNIX prompt collect 

df -k

.

File Transfer Protocol/Secure File Transfer Protocol Transfer Failed—Billing 
(6)

The File Transfer Protocol/Secure File Transfer Protocol Transfer Failed alarm (major) indicates that 
the billing information FTP/SFTP transfer has failed. The primary cause of the alarm is that the BTS 
10200 is unable to connect to remote host. To correct the primary cause of the alarm, verify the remote 
host is reachable. Run the 

show billing-acct-addr

 command and verify that the billing-server-addr is 

correct. Change the billing-server-addr, if necessary, by using the 

change billing-acct-addr

 command. 

The secondary cause of the alarm is that the BTS 10200 is unable to login to remote host. To correct the 
secondary cause of the alarm, use the 

show billing-acct-addr

 command to verify that the user-name is 

a valid user for the host specified in the billing-server-addr. If user-name is correct and the TransferType 
dataword shows FTP, re-enter the password by using the 

change billing-acct-addr

 command. If 

user-name is correct and the TransferType dataword shows SFTP, verify that SSH keys have been 
pre-configured for user-name on both the BTS 10200 and the remote host. The ternary cause of the alarm 
is that a file transfer error occurred. To correct the ternary cause of the alarm, check the Error dataword 
to see if it gives an indication of the kind of error that occurred. It could be a file-system error on the 
remote host, or a communication failure between the BTS 10200 and the remote host. The subsequent 
cause of the alarm is that the CDB_BILLING_SUPP flag is not set to Y in the call-agent-profile table. 
To correct the subsequent cause of the alarm, check and verify that the CDB_BILLING_SUPP flag is 
set to Y in the call-agent-profile table.

Note

OpenSSH version 3.9p1 contains a bug that may cause billing file transfers over SFTP to fail.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands