manualshive.com logo in svg

Cisco BTS 10200 Softswitch, Troubleshooting Manual

Share
Download
Cisco BTS 10200 Softswitch Troubleshooting Manual Download Page 137

 

3-31

Cisco BTS 10200 Softswitch Troubleshooting Guide, Release 5.0.x

OL-8723-19

Chapter 3      Billing Troubleshooting

Monitoring Billing Events

Error Reading Provisioned Data–Using Default—Billing (42)

The Error Reading Provisioned Data–Using Default event functions as a warning that an error occurred 
while reading provisioning data and that the default provisioning data and default values will be used. 
The primary cause of the error is that the application was unable to read provisioned data, and had to 
resort to using default values. Check to ensure a complete load has been installed on the BTS 10200 
system. If the load is complete and problem persists, contact Cisco TAC.

Note

Refer to the 

“Obtaining Documentation and Submitting a Service Request” section on page lvi

 for 

detailed instructions on contacting Cisco TAC and opening a service request.

Record Keeping System Switch Occurred—Billing (44)

The Record Keeping System Switch Occurred alarm (major) indicates that a RKS switch has occurred. 
To troubleshoot and correct the cause of the Record Keeping System Switch Occurred alarm, refer to 
the 

“Record Keeping System Switch Occurred—Billing (44)” section on page 3-40

.

Event Message Log File Opened—Billing (45)

The Event Message Log File Opened alarm (minor) indicates that a event message log file has been 
opened. To troubleshoot and correct the cause of the Event Message Log File Opened alarm, refer to the 

“Event Message Log File Opened—Billing (45)” section on page 3-41

.

Event Message Log File Closed—Billing (46)

The Event Message Log File Closed alarm (minor) indicates that a event message log file has been 
closed. To troubleshoot and correct the cause of the Event Message Log File Closed alarm, refer to the 

“Event Message Log File Closed—Billing (46)” section on page 3-41

.

Record Keeping System Unreachable for One Hour—Billing (47)

The Record Keeping System Unreachable for One Hour alarm (minor) indicates that the RKS servers 
have been unreachable for one hour. To troubleshoot and correct the cause of the Record Keeping 
System Unreachable for One Hour alarm, refer to the 

“Record Keeping System Unreachable for One 

Hour—Billing (47)” section on page 3-41

.

Record Keeping System Unreachable for Three Hours—Billing (48)

The Record Keeping System Unreachable for Three Hours alarm (major) indicates that the RKS servers 
have been unreachable for three hours. To troubleshoot and correct the cause of the Record Keeping 
System Unreachable for Three Hours alarm, refer to the 

“Record Keeping System Unreachable for Three 

Hours—Billing (48)” section on page 3-41

.

Summary of Contents for BTS 10200 Softswitch











































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands