manualshive.com logo in svg

Cisco ASR 914, Manual, Page: 25 / 82

Share
Download
Cisco ASR 914 Manual Download Page 25

Installing the Power Supply

The DC power supply provides option to connect with two different sources (dual feed); positive (+) and
negative (-) are marked on the PSU terminals.

The power on voltage is -42 VDC.

Note

The power supply must be wired before plugging the power supply in the chassis. Ensure the branch circuit
breaker is turned off. Only after installing the power supply in the chassis, should the branch circuit breaker
be turned on. The branch circuit breaker must be turned off before unplugging the power supply.

Caution

Each power supply provides a dual primary input power connection.

Read the installation instructions before connecting the system to the power source. Statement 10

Warning

Preventing Power Loss

Use the following guidelines to prevent power loss to the router.

• To prevent loss of input power, ensure that the total maximum load on each circuit supplying the power

supplies is within the current ratings of the wiring and breakers.

• In some systems, you can use an UPS to protect against power failures at your site. Avoid UPS types

that use ferroresonant technology. These UPS types can become unstable with systems like the Cisco
ASR 914 Router, which can have substantial current draw fluctuations due to bursty data traffic patterns.

For information on power specifications, see

Cisco ASR 900 Series Aggregation Services Routers Data Sheet

.

Power Connection Guidelines

This section provides guidelines for connecting the Cisco ASR 914 Router power supplies to the site power
source.

Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground
conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that
suitable grounding is available. Statement 213

Warning

This product requires short-circuit (overcurrent) protection, to be provided as part of the building installation.
Install only in accordance with national and local wiring regulations. Statement 1045

Warning

Installing the Cisco ASR 914 Router

25

Installing the Cisco ASR 914 Router

Installing the Power Supply

Summary of Contents for ASR 914



















































































Reviews:

No comments