Cisco ASR 914 Manual Download Page 12

Page: 12 / 82

Figure 8: Installing the Fan Tray

While installing the fan tray, align the fan tray towards the right of the chassis. The fans are exposed
on the front of the fan tray without the dust filter. Always handle the fan tray by the handle.

Note

The fan trays are assembled with filters when shipped. You can remove the filters for easy installation
of fan trays. For more information, see

Removing and Replacing the Dust Filter

section.

Note

Step 2

Orient the fan trays so that the captive screws are on the top of the fan tray’s front panel.

Step 3

Guide the fan trays into the chassis until it is fully seated.

Step 4

Secure the fan trays to the chassis using the attached captive installation screws. The recommended maximum
torque is 5.5 in.-lb (.62 N-m).

Fan 1 is the primary fan tray and it is mandatory to run. Without Fan 1 or Fan 2, the Fan 3 runs at
full speed.

Note

For information about connecting cables to the fan tray alarm port, see the

Connecting the Fan Tray Alarm

Port

section. For a summary of the LEDs on the fan tray, see the

LED Summary

section. For more information

about air flow guidelines, see

Air Flow Guidelines

section.

Removing the Dust Filter

Remove the dust filter for a replacement.

Installing the Cisco ASR 914 Router

Removing the Dust Filter

Summary of Contents for ASR 914



















































































Search results

Summary of Contents for ASR 914

Reviews:

Cisco ASR 914, Manual, Page: 12 / 82

Search results

Summary of Contents for ASR 914

Reviews: