Cisco ASR 907 Hardware Installation Manual Download Page 79

Page: 79 / 204

Step 5

Connect the other end of the ground wire to a suitable grounding point at your site.

Installing the Fan Tray

The fan tray is a modular unit that provides cooling to the Cisco ASR 907 Router.

Do not introduce body parts or objects in the fan tray slot when installing or removing the fan tray module.
Exposed circuitry is an energy hazard.

Note

Follow these steps to install the fan tray in the chassis:

Procedure

Step 1

Orient the fan tray so that the captive screws are on the left side of the fan tray’s front panel. The figure below
shows how to orient the fan tray.

Figure 44: Installing the Fan Tray

Step 2

Guide the fan tray into the chassis until it is fully seated.

The fans are exposed on the left side of the fan tray. Keep your fingers, clothing, and jewelry away
from the fans. Always handle the fan tray by the handle.

Caution

Cisco ASR 907 Router Hardware Installation Guide

Installing the Cisco ASR 907 Router

Installing the Fan Tray

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands