Cisco ASR 907 Hardware Installation Manual Download Page 31 | Manualshive

Page: 31 / 204

background image

Figure 13: A900-IMA8CS1Z-M Gigabit Ethernet Interface Module

The following modes are supported for the Interface Module, based on slot capacity:

• 8 x 1GigE (SFP) Fully subscribed mode (FS)

• 8 x 1GigE (SFP) + 1 x 10GigE (SFP+) Fully subscribed mode (FS)

• 16 x 1GigE (C-SFP) + 1 x 10GigE (SFP+) Fully subscribed mode (FS)

• 16 or 18 x 1GigE (C-SFP) Oversubscribed mode (OS)

• 16 x 1GigE (C-SFP) + 1 x 10GigE (SFP+) Oversubscribed mode (OS)

• 8 or 9 x 1GigE (SFP) Fully subscribed mode (FS)

• 1 x 10GigE (SFP+) Fully subscribed mode (FS)

For information on supported SFP modules, see

Cisco ASR 900 Series Aggregation Services Routers Data

.

For more information on port numbering, see

Configuring 1-port 10 Gigabit Ethernet (1 X SFP+) / 1-port

Gigabit Ethernet (1 X SFP) / 2-port Gigabit Ethernet (1 X CSFP) and 16-port Gigabit Ethernet (8 X CSFP)
/ 8-port Gigabit Ethernet (8 X SFP) Interface Module

chapter of the

Cisco ASR 900 Router Series Configuration

Guide, Cisco IOS XE Everest 16.6.1

.

16-Port T1/E1 Interface Module (A900-IMA16D)

The 16-port T1/E1 interface module provides connectivity for up to 16 T1/E1 ports through a 100-pin Amplimite
connector. The 16-port T1/E1 interface module requires the use of a patch panel to provide RJ48 (T1) or BNC
(E1) connectors. The figure below shows the interface module.

Cisco ASR 907 Router Hardware Installation Guide

21

Cisco ASR 907 Router Overview

16-Port T1/E1 Interface Module (A900-IMA16D)

«
...
29
30
31
32
33
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Univerge SV8100

Brand: NEC Pages: 44

Brand: Paradyne Pages: 22

IntelliJack NJ200

Brand: 3Com Pages: 4

SR8800 IM-FW-II

Brand: H3C Pages: 107

Brand: 3Com Pages: 12

Brand: H3C Pages: 16

H3C S3600 Series

Brand: H3C Pages: 10

Brand: H3C Pages: 42

Brand: H3C Pages: 2

H3C S7500E Series

Brand: H3C Pages: 34

Brand: H3C Pages: 33

Brand: H3C Pages: 14

Brand: H3C Pages: 56

H3C S7500E Series

Brand: H3C Pages: 112

Brand: H3C Pages: 15

SR8800 IM-FW-II

Brand: H3C Pages: 5

H3C S7500E Series

Brand: H3C Pages: 50

Brand: H3C Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands