Cisco ASR 907 Hardware Installation Manual Download Page 24

Page: 24 / 204

• chOC3/STM1 with ATM and CE—Supports (as low as DS0 although not for all channels simultaneously)

• chOC12/STM4 with ATM and CE—Supports (as low as DS0 although not on all channels simultaneously)

• OC3c/STM1c with ATM and CE

• OC12c/STM4c with ATM and CE

• DS3 through RAD SFPs in GE IM

• 100GE CPAK ports using 1x100G IM

• 100GE QSFP28 using 1x100G IM

• 100GE QSFP using 2x100G IM

• T1/E1 ports with integrated inter-office surge protection-Supports TDM channelized, PWE3 processing

• T3/E3 ports - Supports TDM channelized, PWE3 Processing

• OC3/OC12/OC48/OC192 - Supports TDM channelized, PWE3 Processing

For information about supported interface modules, see the data sheet for the

Cisco ASR 900 Series Aggregation

Services Routers

Note

For more information about installing, see the

Installing an Interface Module

8-Port 1 Gigabit Ethernet SFP Interface Module (A900-IMA8S)

The Gigabit Ethernet Small Form-Factor Pluggable (SFP) interface module provides eight Gigabit Ethernet
SFP modules. The figure below shows the 8-port 1 GE Gigabit Ethernet SFP interface module.

Figure 3: 8-port 1 GE Gigabit Ethernet SFP Interface Module

Cisco ASR 907 Router Hardware Installation Guide

Cisco ASR 907 Router Overview

8-Port 1 Gigabit Ethernet SFP Interface Module (A900-IMA8S)

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands