Cisco ASR 907 Hardware Installation Manual Download Page 22 | Manualshive

Page: 22 / 204

background image

Table 5: Supported Interface Modules and Part Numbers for N560-RSP4 and N560-RSP4-E

Slot

Part Number

Interface Modules

RSP Module

Not Supported

A900-IMA8S

8-port Gigabit Ethernet SFP Interface
Module (8X1GE)

N560-RSP4
and
N560-RSP4-E

Not Supported

A900-IMA8T

8-port Gigabit Ethernet RJ45
(Copper) Interface Module (8X1GE)

Not Supported

A900-IMA1X

1-port 10 Gigabit Ethernet XFP
Interface Module (1X10GE)

Not Supported

ASR900-IMA8S1Z

SFP Combo IM—8-port Gigabit
Ethernet (8X1GE) + 1-port 10 Gigabit
Ethernet (1X10GE)

Not Supported

ASR900-IMA8T1Z

Copper Combo IM—8-port Gigabit
Ethernet (8X1GE) + 1-port 10 Gigabit
Ethernet Interface Module (1X10GE)

Not Supported

ASR900-IMA2Z

2-port 10 Gigabit Ethernet Interface
Module (2X10GE)

7,9

N560-IMA2C

2x100G Interface module

0,1,2,3,4,5,6,7,8,9,10,11,12,13,14
and 15

A900-IMA8CS1Z-M

8-port SFP/8-port CSFP Gigabit
Ethernet (8/16X1GE) + 1-port 10
Gigabit Ethernet (1X10GE) Interface
module

4,5,7,9,10 and 11

A900-IMA8Z

8x10G Interface module

RSP Redundancy

The Cisco ASR 907 Router chassis includes two RSP slots to allow for redundant RSPs. When the router uses
redundant RSPs, one RSP operates in the active mode and the other operates in the hot standby mode. Removal
or failure of the active RSP results in an automatic switchover to the standby RSP.

If you are using redundant RSPs, both the RSPs must be of the same type because a mixed configuration of
two different RSP types is not supported.

Note

Network Timing Interfaces

The RSP supports the following network timing interfaces:

• BITS input/output port—RJ48 jack
• 1 PPS input and output—Mini coax connectors
• 2.048 or 10 MHz input and output—Mini coax connectors
• Time of Day (ToD) or 1 PPS input or output port—Shielded RJ45 jack

Cisco ASR 907 Router Hardware Installation Guide

12

Cisco ASR 907 Router Overview

RSP Redundancy

«
...
20
21
22
23
24
...
»

Summary of Contents for ASR 907













































































































































































































Reviews:

No comments

Related manuals for ASR 907

Express Ethernetwork DI-704P

Brand: D-Link Pages: 17

Wireless Router

Brand: Watchguard Pages: 11

Brand: D-Link Pages: 32

Brand: D-Link Pages: 28

Brand: D-Link Pages: 48

Brand: D-Link Pages: 83

Brand: D-Link Pages: 155

Brand: Wave wifi Pages: 2

Brand: N-Tron Pages: 138

Brand: National Instruments Pages: 34

Brand: Salusfin Pages: 6

Brand: Funkwerk Pages: 2

Brand: Black Box Pages: 37

Brand: ZyXEL Communications Pages: 116

Octopus G Series

Brand: TwinMOS Pages: 29

Hotwire 8775 MSDSL

Brand: Paradyne Pages: 10

SteelCentral AppResponse 2180

Brand: Riverbed Pages: 82

ApplianceStor 15MT

Brand: Rasilient Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands