Cisco ASR 907 Hardware Installation Manual Download Page 199

Page: 199 / 204

Description (two LEDs for eachT1/E1 port)

Color/State

LED

Disabled or power down

Off

IM power rails are in range and are enabled

Green

PWR

Disabled; No power to IM

Off

Serial Interface Module LEDs

The table below summarizes the LEDs for the serial interface module.

Table 40: Cisco ASR 907 Router Serial IM LEDs

Meaning

Color/State

LED Label

All power rails are within spec.

Green

Power (PWR)

Disabled

Red

No Power

Off

Failure

Red

Operating Status (STAT)

Booting (if IM has a local CPU)

Yellow

Operational

Green

No Power

Off

At least one of the 4 ports is in an up state.

Green

68-Pin Connector LEDs

At least one of the 4 ports is passing traffic

Blinking Green

All four ports are successfully initialized and in a down state

Solid Yellow

At least one of the port has failed

Blinking
Yellow

All the ports are not enabled (at POR)

Off

Port is passing traffic

Green

12-in-1 Connector LEDs

Port successfully initialized and in a down state

Solid Yellow

Port has failed

Blinking
Yellow

Not Enabled (at POR)

Off

Power Supply LEDs

The table below summarizes the power supply LEDs for both the AC and DC power supplies.

Cisco ASR 907 Router Hardware Installation Guide

189

Troubleshooting

Serial Interface Module LEDs

Summary of Contents for ASR 907












































































































































































































Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands

Cisco ASR 907, Hardware Installation Manual

Search results

Summary of Contents for ASR 907

Reviews:

Related manuals for ASR 907

Brands by name

Popular brands