Cisco ASR 901S Series Installation Manual Download Page 68

Page: 68 / 106

Using Cable Glands

This section describes how to use cable glands with router cables that are threaded through the chassis cable
ports.

Materials Required

•

Cable gland (part number: 51-6436-01) (Cisco-supplied)

•

33-mm A/F suitable wrench to remove the hexagonal lock nut from the router (customer-supplied)

•

15/16-inch (24 mm) open-end wrench (customer-supplied)

Figure 33: Cable Gland Components

Description

Name

Item

Connects directly to the chassis cable port on the router.

Adapter gland

Fits over the cable and creates an liquid-tight seal inside the glands.

Split gasket

Covers unused ports of the cable gland because dust caps cannot
be used when a cable gland port is in use.

Billet plug

Secures the split gasket over the cable.

Grommet/lock nut

Cable Requirements

Cables used with the cable glands should meet the following criteria:

•

Outdoor-rated

•

UV-stabilized

•

Diameter of 0.25 to 0.29 inches (6.5 to 7.5 mm)

Cisco ASR 901S Series Aggregation Services Router Hardware Installation Guide

OL-29732-01

Installing the Router

Using Cable Glands

Summary of Contents for ASR 901S Series











































































































Search results

Summary of Contents for ASR 901S Series

Reviews:

Related manuals for ASR 901S Series

Brands by name

Popular brands

Cisco ASR 901S Series, Installation Manual

Search results

Summary of Contents for ASR 901S Series

Reviews:

Related manuals for ASR 901S Series

Brands by name

Popular brands