manualshive.com logo in svg

Cisco ASR 5500, System Administration Manual

The Cisco ASR 5500 is a cutting-edge networking solution that empowers businesses with exceptional performance and reliability. For hassle-free installation, our detailed Installation Manual is available for free download from manualshive.com, ensuring seamless setup and optimal usage. Get the most out of your product effortlessly.

Share
Download
background image

The following command configures the maximum number of equal cost paths that can be submitted by a
routing protocol:

config

context context_name

ip routing maximum-paths [ max_num ]

Notes:

•

max_num

is an integer from 1 through 10 (

releases prior to 18.2

) or 1 through 32 (

release 18.2+

).

•

Save your configuration as described in the

Verifying and Saving Your Configuration

chapter.

BGP-4 Routing

The Border Gateway Protocol 4 (BGP-4) routing protocol is supported through a BGP router process that is
implemented at the context level.

Border Gateway Protocol (BGP) is an inter-AS routing protocol. An Autonomous System (AS) is a set of
routers under a single technical administration that use an interior gateway protocol and common metrics to
route packets within the AS. The set of routers uses an exterior gateway protocol to route packets to other
autonomous systems.

BGP runs over TCP. This eliminates the need for the BGP protocol to implement explicit update fragmentation,
retransmission, acknowledgement, and sequencing information. Any authentication scheme used by TCP may
be used in addition to BGP's own authentication mechanisms.

BGP routers exchange network reachability information with other BGP routers. This information builds a
picture of AS connectivity from which routes are filtered and AS-level policy decisions are enforced.

BGP-4 provides classless inter-domain routing. This includes support for advertising an IP prefix and eliminates
the concept of network class within BGP. BGP-4 also allows the aggregation of routes, including the aggregation
of AS paths.

On the ASR 5500, BGP routes with IPv6 prefix lengths less than /12 and between the range of /64 and
/128 are not supported.

Important

Overview of BGP Support

Mobile devices communicate to the Internet through Home Agents (HAs). HAs assign IP addresses to the
mobile node from a configured pool of addresses. These addresses are also advertised to Internet routers
through an IP routing protocol to ensure dynamic routing. The BGP-4 protocol is used as a monitoring
mechanism between an HA and Internet router with routing to support Interchassis Session Recovery (ICSR).
(Refer to

Interchassis Session Recovery

for more information.)

The objective of BGP-4 protocol support is to satisfy routing requirements and monitor communications with
Internet routers. BGP-4 may trigger an active to standby switchover to keep subscriber services from being
interrupted.

The following BGP-4 features are supported:

•

Exterior Border Gateway Protocol (EBGP) multi-hop

ASR 5500 System Administration Guide, StarOS Release 21.5    

215

Routing

BGP-4 Routing

Summary of Contents for ASR 5500















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 5500

NetApp AAF A700 Manual preview
AAF A700
Brand: NetApp Pages: 19
Advantech HPC-7483 User Manual preview
HPC-7483
Brand: Advantech Pages: 42
WP XACT PRO 7448 Owner'S Manual preview
XACT PRO 7448
Brand: WP Pages: 30
ICP Electronics RACK-360 User Manual preview
RACK-360
Brand: ICP Electronics Pages: 9
ICP Electronics EC-1040 User Manual preview
EC-1040
Brand: ICP Electronics Pages: 26
Supermicro SC825MS-R700LPB User Manual preview
SC825MS-R700LPB
Brand: Supermicro Pages: 63
VIA Technologies AMOS-5110 Quick Manual preview
AMOS-5110
Brand: VIA Technologies Pages: 2
StorCase Technology InfoStation User Manual preview
InfoStation
Brand: StorCase Technology Pages: 49
Planet WMC-1600R User Manual preview
WMC-1600R
Brand: Planet Pages: 26
JYTEK PXI-62700 User Manual preview
PXI-62700
Brand: JYTEK Pages: 32
JYTEK PXIe-62780 User Manual preview
PXIe-62780
Brand: JYTEK Pages: 35

Brands by name

Popular brands

Load more brands