Cisco ASR 1001-X Hardware Installation Manual Download Page 40

Page: 40 / 152

your site configuration

before

installation. After installation, make sure the site maintains the environmental

characteristics, as shown in the below table.

Table 11: Cisco ASR 1001-X Router Environmental Tolerance

Maximum

Minimum

Environmental Characteristic

40° C

(40° C up to 10,000 feet)

0° C

Operating temperature (nominal)

50° C

0° C

Operating temperature (short term)

+70° C

–

20° C

Storage temperature

90%

10%

Operative humidity (nominal)
(relative humidity)

90%

Operative humidity (short term)

95%

Storage humidity (relative
humidity)

10,000 feet

–

500 feet

Altitude, operating: over allowable
temperature range (0 to 50 degrees
C)

50,000 feet

–

1000 feet

Altitude, nonoperating: over
allowable temperature range

+70° C

–

25° C

Thermal shock nonoperating with
change over time of 3 minutes

+50° C

0° C

Thermal Shock - Operating at 2.5
degree C per minute

Physical Characteristics

Be familiar with the physical characteristics of the Cisco ASR 1001-X Router to assist you in placing the
system at a proper location.

For information regarding rack widths supported for the Cisco ASR 1001-X Router, see the following sections:

The below table shows the weight and dimensions of the Cisco ASR 1001-X Routers.

Table 12: Physical Characteristics of Cisco ASR 1001-X Router

Cisco ASR 1001-X

Characteristic

1.71 in. (43.43 mm)

—

1RU; rack-mount per EIA

RS-310

Height

Cisco ASR 1001-X Router Hardware Installation Guide

Preparing Your Site for Installation

Site Selection Guidelines

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 40 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: