Cisco ASR 1001-X Hardware Installation Manual Download Page 20

Page: 20 / 152

Description

Component

1 half-height (HH) SPA bay

SPA Slots

NIM Slots

USB Slots

Supported Half-Height SPAs

The following table lists the supported half-height SPAs on the Cisco ASR 1001-X Router.Supported
Half-Height SPAs

Table 3: Supported Half-Height SPAs

Description

PID

Cisco 1-Port 10GE LAN-PHY

SPA-1X10GE-L-V2

1-port Channelized STM-1/OC-3c to DS0

SPA-1XCHSTM1/OC3

1-port OC12/STM4 POS

SPA-1XOC12-POS

2-port OC12/STM4 POS

SPA-2XOC12-POS

4-port OC-12/STM-4 POS

SPA-4XOC12-POS

8-port OC12/STM4

SPA-8XOC12-POS

1-port OC-3c/STM-1 ATM

SPA-1XOC3-ATM-V2

Cisco 2-Port Gigabit Ethernet

SPA-2X1GE-V2

2-port Channelized T3 to DS0

SPA-2XCT3/DS0

2-port OC3/STM1 POS

SPA-2XOC3-POS

8-port OC-3/STM-1 POS

SPA-8XOC3-POS

1-port OC48/STM16 POS/RPR

SPA-1XOC48POS/RPR

2-port OC48/STM16 POS/RPR

SPA-2XOC48POS/RPR

2-port Clear Channel T3/E3

SPA-2XT3/E3

3-port OC-3c/STM-1 ATM

SPA-3XOC3-ATM-V2

Cisco 4-Port Fast Ethernet (TX)

SPA-4X1FE-TX-V2

Cisco ASR 1001-X Router Hardware Installation Guide

Cisco ASR 1001-X Router Supported Hardware Components

Supported Half-Height SPAs

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 20 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: