Cisco ASR 1001-X Hardware Installation Manual Download Page 19

Page: 19 / 152

C H A P T E R

Cisco ASR 1001-X Router Supported Hardware
Components

This chapter contains information about the supported hardware components on the Cisco ASR 1001-X
Router, and contains the following sections:

•

Supported Hardware Components, page 11

•

Supported Half-Height SPAs, page 12

•

Supported Small Form-Factor Pluggable (SFP and SFP+) Transceivers, page 14

•

Supported NIMs, page 15

•

Cisco ASR 1001-X Router Power Supplies, page 17

Supported Hardware Components

The following table lists the hardware components supported on the Cisco ASR 1001-X Router.

Table 2: Supported Hardware Components

Description

Component

1 RU form factor

Chassis

Six built-in Gigabit Ethernet and two built-in
10-Gigabit Ethernet ports

Ethernet Ports

A nonmodular, fixed ESP with a default throughput
of 2.5 Gbps, which is upgradable with a
software-activated performance license of 5 Gbps,
10 Gbps, or 20 Gbps.

ESP

Single integrated route processor

Route Processor

Integrated SIP

SIP

Cisco ASR 1001-X Router Hardware Installation Guide

Summary of Contents for ASR 1001-X
























































































































































Search results

Summary of Contents for ASR 1001-X

Reviews:

Cisco ASR 1001-X, Hardware Installation Manual, Page: 19 / 152

Search results

Summary of Contents for ASR 1001-X

Reviews: