manualshive.com logo in svg

Cisco ASR 1001-HX, Removing And Replacing, Page: 3 / 30

Share
Download
Cisco ASR 1001-HX Removing And Replacing Download Page 3

Figure 2: Cisco ASR 1001-HX Router Crypto Module

Crypto module

2

Screws

1

Step 7

Install the cover.

Step 8

Install the chassis in the rack.

Step 9

Power up the router by plugging in the power supplies and placing the chassis power switch to the On position.

Step 10

Use the

show platform hardware crypto-device 0 status

command to verify successful installation:

Router#

show platform hardware crypto-device 0 status

Encryption processor is functional

Removing and Replacing the Crypto Module in a Cisco ASR 1002-HX Router

Before you begin

To install the crypto module, you must shut down the router and remove it from the rack. Enter the

copy

running-config startup-config

command to save the configuration to NVRAM.

Procedure

Step 1

Power down the router by placing the chassis power switch in the Standby position and unplug the power
supplies.

Step 2

Remove the router from the rack.

Step 3

Open the access panel on the right side of the chassis by removing the 5 screws, as shown in the following
figure.

Removing and Replacing FRUs

3

Removing and Replacing FRUs

Removing and Replacing the Crypto Module in a Cisco ASR 1002-HX Router

Summary of Contents for ASR 1001-HX































Reviews:

No comments