manualshive.com logo in svg

Cisco ASR 1001-HX, Removing And Replacing, Page: 21 / 30

Share
Download
Cisco ASR 1001-HX Removing And Replacing Download Page 21

We recommend that you have the following tools and parts readily available for installing a NIM:

• Number 2 Phillips or a 3/16-inch flat-blade screwdriver

• NIM

• Cables

• Your own ESD-prevention equipment or the disposable grounding wrist strap included with all upgrade

kits, FRUs, and spares

• Antistatic mat or surface, or static shielding bag

If you need additional equipment, contact a Cisco service representative for ordering information.

For information about electrostatic discharge prevention, see the “Electrostatic Discharge Prevention” section
on page 7-15.

Removing a NIM

Procedure

Step 1

Attach an ESD wrist strap between you and an unpainted chassis surface.

Step 2

Stop the NIM so that there is no traffic running through the NIM when it is removed, using the following
steps:

Removing a NIM while traffic is flowing through the ports may cause system disruption.

Note

a) At the

router#

prompt, enter

hw-module subslot 0/3 stop

and press

Enter

.

b) At the

router#

prompt, enter

end

and press

Enter

.

Step 3

Disconnect all the cables from the NIM.

Step 4

Unscrew the captive installation screws on either side of the NIM.

Figure 18: Captive Installation Screws Location

Captive screws on the NIM

1

Step 5

Pull out the NIM out of the chassis.

Step 6

Place the NIM in an antistatic bag to protect it from electrostatic discharge (ESD) damage.

Removing and Replacing FRUs

21

Removing and Replacing FRUs

Removing a NIM

Summary of Contents for ASR 1001-HX































Reviews:

No comments