manualshive.com logo in svg

Cisco 807, Hardware Installation Manual, Page: 28 / 44

Share
Download
Cisco 807 Hardware Installation Manual Download Page 28

26

      

  

Figure 5

S0 and S1 Characteristics

Figure 6

S0 and S1 Details

Accessories

See 

Table 6

 for a partial listing of IR807 Accessories.

Depending on your particular model of the router, there will be either a single hole or double hole grounding.

53-100629-01 - Contains Getting started with the Cisco 807 Integrated Services Router document, associated 
hardware, and the single hole grounding kit.

53-100797-01 - Contains Getting started with the Cisco 807 Integrated Services Router document, associated 
hardware, and the two hole grounding kit.

Pin Number

Description

Abbreviation

DTE

DCE

1

DCE Ready, Ring Indicator

DSR/RI

<—

—>

2

Received Line Signal Detector

DCD

<—

—>

3

DTE Ready

DTR

—>

<—

4

Signal Ground

COM

5

Received Data

RxD

<—

—>

6

Transmitted Data

TxD

—>

<—

7

Clear To Send

CTS

<—

—>

8

Request To Send

RTS

—>

<—

Table 6

Cisco IR807 Accessories

Cisco Part Number

Accessory

PWR-IE50W-AC

DIN-rail mount AC/DC power supply - Input AC 100-240V/1.25A or 
Input DC 125-250V/1A, Output DC 24V/2.1A

IR807-DINRAIL(=)

Din rail kit and mounting screws

IR807-WALLMNT(=)

Wall mount kit and mounting screws

CAB-CONSOLE-USB 
37-1090-01 

Cisco USB Type A Male to Mini B Male 6ft Console Cable 

Summary of Contents for 807













































Reviews:

No comments