manualshive.com logo in svg

Cisco 7600-SIP-400 - SPA Interface Processor 400, Hardware Installation Manual, Page: 64 / 172

Share
Download
Cisco 7600-SIP-400 - SPA Interface Processor 400 Hardware Installation Manual Download Page 64

 

3-18

Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide

OL-5052-14

Chapter 3      Overview: Cisco 7600 Series Router Shared Port Adapters

  1-Port Clear Channel OC-3, 3-Port Clear Channel OC-3, and 1-Port Clear Channel OC-12 ATM SPA Version 2 Overview

2-Port and 4-Port OC-3c/STM-1 ATM SPA Cables and Connectors

The 2-Port and 4-Port OC-3c/STM-1 ATM SPAs provide the following optical fiber options:

  •

Multimode—155-Mbps, OC-3 optical fiber (SONET STS-3c or SDH STM-1)

Use a multimode optical fiber that has a core/cladding diameter of 62.5/125 microns. 

  •

Single-mode—155-Mbps, OC-3 optical fiber (SONET STS-3c or SDH STM-1)

Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns. (Nominal 
diameter is approximately 10/125 microns.)

For single-mode and multimode optical fiber connections, you can use either a duplex LC-type cable (see 

Figure 3-12

) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX).

Figure 3-12

Duplex Patch Cable with LC-Type Connectors

Use single-mode (for intermediate- or long-reach configurations) or multimode optical fiber cable to 
connect your router to a network or to connect two OC-3-equipped routers back-to-back. 

Long-range SFP optics modules (for long-reach configurations) cannot be connected back-to-back 
without using an attenuator between the two of them.

1-Port Clear Channel OC-3, 3-Port Clear Channel OC-3, and 
1-Port Clear Channel OC-12 ATM SPA Version 2 Overview

The ATM SPA version 2 comprises these channels:

  •

1-Port Clear Channel OC-3 ATM SPA Version 2 (SPA-1xOC3-ATM-V2)

  •

3-Port Clear Channel OC-3 ATM SPA Version 2 (SPA-3xOC3-ATM-V2)

  •

1-Port Clear Channel OC-12 ATM SPA Version 2 (SPA-1xOC12-ATM-V2)

The SPA-1xOC3-ATM-V2, SPA-3xOC3-ATM-V2, and SPA-1xOC12-ATM-V2 is a single-height SPA 
that installs into one SIP subslot. The Clear Channel OC-3 ATM SPA with SFP optical transceiver 
modules provides SONET and SDH network connectivity with a per-port bandwidth of 155.52 Mbps. 
The Clear Channel OC-12 ATM SPA with small form-factor pluggable (SFP) optical transceiver 
modules provides SONET and SDH network connectivity with a per-port bandwidth of 622 Mbps. For 
more information about SPA bandwidth, see the “

Bandwidth Oversubscription

” section in this chapter.

These sections describe the SPA-1xOC3-ATM-V2, SPA-3xOC3-ATM-V2, and SPA-1xOC12-ATM-V2:

  •

1-Port Clear Channel OC-3, 3-Port Clear Channel OC-3, and 1-Port Clear Channel OC-12 ATM SPA 
Version 2 LEDs, page 3-19

  •

1-Port Clear Channel OC-3, 3-Port Clear Channel OC-3, and 1-Port Clear Channel OC-12 ATM SPA 
Version 2 Interface Specifications, page 3-20

/ /

/ /

/ /

TX

RX

84929

Summary of Contents for 7600-SIP-400 - SPA Interface Processor 400













































































































































































Reviews:

No comments