manualshive.com logo in svg

Cisco 7600-SIP-400 - SPA Interface Processor 400, Hardware Installation Manual, Page: 50 / 172

Share
Download
Cisco 7600-SIP-400 - SPA Interface Processor 400 Hardware Installation Manual Download Page 50

 

3-4

Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide

OL-5052-14

Chapter 3      Overview: Cisco 7600 Series Router Shared Port Adapters

  Bandwidth Oversubscription

Cisco 7600 SIP-400 Oversubscription Guidelines

As of Cisco IOS Release 12.2(18)SXF, when using the Cisco 7600 SIP-400 with the 2-Port Gigabit 
Ethernet SPA or the 1-Port OC-48c/STM-16 ATM SPA, consider the following oversubscription 
guidelines:

  •

The Cisco 7600-SIP-400 only supports installation of one 1-Port OC-48c/STM-16 ATM SPA 
without any other SPAs installed in the SIP.

  •

The Cisco 7600-SIP-400 supports installation of up to two 2-Port Gigabit Ethernet SPAs without 
any other SPAs installed in the SIP.

  •

The Cisco 7600-SIP-400 supports installation of any combination of a OC-3, OC-12 POS, CEoP, or 
ATM SPAs, up to a combined ingress bandwidth of OC-48 rates.

  •

The Cisco 7600-SIP-400 supports installation of any combination of OC-3, OC-12 POS, CEoP, or 
ATM SPAs up to a combined ingress bandwidth of OC-24 rates, when installed with a single 2-Port 
Gigabit Ethernet SPA.

  •

The Cisco 7600-SIP-400 supports installation of a single 1-Port 10-Gigabit Ethernet SPA without 
any other SPAs installed in the 7600-SIP-400.

Note

A 1-Port 10-Gigabit Ethernet SPA on a 7600-SIP-400 provides 4 Gbps of bandwidth.

  •

A maximum of 32 total ingress SPI-4 ports are supported on the SIP-400. Ethernet SPAs use 2 SPI 
Port per interface. If a SPA which causes the total required SPI-4 ports on SIP-400 to exceed 32, that 
SPA will not be permitted to power up. 

 

For example, if you insert the SPA-5x1GE into the SIP-400, where SPAs already inserted have 
consumed at least 23 SPI ports, the following error message will be posted on the console: 

SPI-4 port limit exceeded, SPA-5X1GE in subslot 3 has been powered down.

  •

The Cisco 7600 supports four 4-port FE SPAs or two 8-port FE SPA in SIP-400 in one shot

The following table lists the different SPA types and the total SPI ports consumed by them on a SIP-400: 

SPA PID

Total SPI ports consumed

POS SPAs

SPA-1XOC12-POS 

1

 SPA-2XOC3-POS     

2

 SPA-4XOC3-POS 

4

 SPA-1XOC48-POS

1

Ethernet SPAs

 SPA-2XGE      

4

 SPA-2XGE-V2    

4

 SPA-5XGE-V2    

10

 SPA-1X10GE-V2  

2

SPA-4XFE-TX-V2  

8

SPA-8XFE-TX-V2 

16

ATM SPAs

SPA-2XOC3-ATM 

2

Summary of Contents for 7600-SIP-400 - SPA Interface Processor 400













































































































































































Reviews:

No comments