Home
/
Cisco
/
7600-SIP-400 - SPA Interface Processor 400
/
Hardware Installation Manual

Cisco 7600-SIP-400 - SPA Interface Processor 400, Hardware Installation Manual, Page: 142 / 172

Share

Page: 142 / 172

Cisco 7600-SIP-400 - SPA Interface Processor 400 Hardware Installation Manual Download Page 142

5-4

Cisco 7600 Series Router SIP, SSC, and SPA Hardware Installation Guide

OL-5052-14

Chapter 5 Installing and Removing a SIP

Online Insertion and Removal

The following example shows that the Cisco 7600 SIP-400 located in slot 13 is deactivated. This is
indicated by its “PwrDown” status.

Router#

show module 13

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

13 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAB0851042X

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

13 00e0.aabb.cc00 to 00e0.aabb.cc3f 0.525 12.2(PP_SPL_ 12.2(PP_SPL_ Ok

Mod Online Diag Status

--- -------------------

13 PwrDown

To verify activation and proper operation of a SIP, enter the

show module

command and observe “Ok”

in the Status field as shown in the following example:

Router#

show module 2

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

2 0 4-subslot SPA Interface Processor-200 7600-SIP-200 JAB074905S1

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

2 0000.0000.0000 to 0000.0000.003f 0.232 12.2(2004082 12.2(2004082

Ok

Mod Online Diag Status

--- -------------------

2 Pass

Preparing for Online Removal of a SPA

The Cisco 7600 series router supports OIR of a SPA independently of removing the SIP or SSC. This
means that a SIP can remain installed in the router with one SPA remaining active, while you remove
another SPA from one of the SIP subslots. If you are not planning to immediately replace a SPA into the
SIP, then be sure to install a blank filler plate in the subslot. The SIP should always be fully installed
with either functional SPAs or blank filler plates.

The interface configuration is retained (recalled) if a SIP or SPA is removed and then replaced with one
of the same type. This is not the case if you replace a Cisco 7600 SIP-200 with a Cisco 7600 SIP-400 or
vice versa.

If you are planning to remove a SIP along with its SPAs, then you do not need to follow the instructions
in this section. To remove a SIP, see the

“Preparing for Online Removal of a SIP or SSC” section on

page 5-2

.

Note

If you move the SPA (SPA-8XTE1/ SPA-4xCT3/DS0 / SPA-2xCT3/DS0/SPA-1xCHSTM1/OC3) from
one LC to another type of LC in the same bay and same slot, the system will not retain the configuration
of the old interface.

«
...
140
141
142
143
144
...
»

Summary of Contents for 7600-SIP-400 - SPA Interface Processor 400













































































































































































Reviews:

No comments