Cisco 7300-1OC12POS-MM Installation And Configuration Manual Download Page 35 | Manualshive

Page: 35 / 50

background image

3-5

OC12 Packet Over SONET Line Card Installation and Configuration

OL-3437-01

Chapter 3 Removing and Installing Line Cards

Connecting OC12 POS Line Card Interface Cables

Connecting OC12 POS Line Card Interface Cables

To continue your OC12 POS line card installation, you must connect the interface cables.

Note

Optical fiber cables are not available from Cisco Systems; they are available from outside commercial
cable vendors. (For more information on the cables you should use with this line card, see the

POS Line Card Optical Fiber Specifications” section on page 1-5

“Cables and Connectors”

section on page 1-8

To connect cables to the OC12 POS line card, attach one duplex or two simplex optical fiber cables
between the OC12 interface port on your OC12 POS line card and your network.

Ensure that you observe the proper relationship of receive (RX) cable to RX SC-type receptacle and
transmit (TX) cable to TX SC-type receptacle on the OC12 POS line card.

Warning

Because invisible laser radiation may be emitted from the aperture of the port when no
fiber cable is connected, avoid exposure to laser radiation and do not stare into open
apertures.

Warning

Class 1 laser product.

«
...
33
34
35
36
37
...
»

Summary of Contents for 7300-1OC12POS-MM



















































Reviews:

No comments

Related manuals for 7300-1OC12POS-MM

Brand: ZETRON Pages: 3

Brand: Danfoss Pages: 32

PVG 16 PVH/Covers

Brand: Danfoss Pages: 112

Brand: Danfoss Pages: 44

PVG 16 PVH/Covers

Brand: Danfoss Pages: 144

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 64

Brand: Danfoss Pages: 8

VLT AutomationDrive FC 360

Brand: Danfoss Pages: 60

Brand: Danfoss Pages: 6

Brand: Danfoss Pages: 4

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 2

ECL Comfort 110

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 24

Brand: VAT Pages: 27

Brand: ICP DAS USA Pages: 148

Brand: ICMA Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands