manualshive.com logo in svg

Cisco 4000 Series, Hardware Installation Manual, Page: 185 / 206

Share
Download
Cisco 4000 Series Hardware Installation Manual Download Page 185

 

5-61

Hardware Installation Guide for Cisco 4000 Series Integrated Services Routers

OL-32185-02

Chapter 5      Install and Upgrade Internal Modules and FRUs

  Replace a Fan Tray

Replace a Fan Tray

The Cisco  4000  Series ISRs have hot-swappable fan trays that are field replaceable units (FRUs). The 
fan tray includes all router fans in one assembly. If a fan fails, replace the tray using a flat-blade or 
Phillips screwdriver.

Note

The Cisco 4331 ISR and Cisco 4321 ISR do not have hot-swappable fan trays.

Before Hot-Swapping a Fan Tray

Before hot-swapping a fan tray, read the safety precautions below.

•

Read the entire procedure and have the required tools available.

•

Do not attempt the hot-swap in ambient air temperature above 90°F (32°C).

•

Do not attempt the hot-swap at an altitude above 6000 feet (1829 meters).

•

When the router is being operated, we recommend to change the fans in the router within 2 minutes 
to ensure the router does not overheat:

Replace Fan Tray

Note

If hot-swapping the fan tray, we recommend to complete the operation within two minutes to ensure the 
router remains within operating temperature.

Note

We recommend that you change the air filter every 3 months. However, examine the air filter once a 
month (or more often in dusty environments) and replace it if it appears to be excessively dirty or 
damaged. To comply with Telecordia GR-63-Core standard air filter requirements for NEBS 
deployment, the air filter must be replaced, not cleaned.

Step 1

Remove the bezel. The bezel is secured with snap latches. To remove the bezel, hold the top and bottom 
and pull the bezel.

Step 2

Completely loosen the three captive fan tray screws.

Step 3

Pull the fan tray out.

Step 4

Insert the replacement fan tray and tighten the three captive screws.

Step 5

Replace the bezel.

Summary of Contents for 4000 Series















































































































































































































Reviews:

No comments