manualshive.com logo in svg

Cisco 1800 Series, Hardware Installation Manual, Page: 76 / 82

Share
Download
Cisco 1800 Series Hardware Installation Manual Download Page 76

 

7-6

Cisco 1800 Series Integrated Services Routers (Fixed) Hardware Installation Guide

OL-6425-03

Chapter 7      Installing and Upgrading Internal Modules

  Installing the Chassis Cover

Warning

Installation of the equipment must comply with local and national electrical codes. 

Statement 1074

Caution

Ensure that the inline power supply is not connected to the back of the router prior to installation of the 
inline power supply card. Failure to do so may result in damage to the inline power supply card or to the 
router.

Caution

When installing the inline power supply card, ensure that the card is installed in the proper direction. 
Improper installation will result in damage to the inline power supply card. Installation of the inline 
power supply card requires the installation of three metal standoffs, to which the card is then secured 
using three screws. Be sure to use all three screws to ensure that the card is installed properly—if the 
card is not installed in the correct direction, the three screw holes will not match up with the three metal 
standoffs.

Step 1

Find the metal standoff attachment locations on the system board, which are indicated by a star pattern 
surrounding each of the three holes in the system board.

Step 2

Install the three metal standoffs into the system board in the metal standoff attachment locations 
(denoted by a star pattern around the holes). Use a 1/4-inch nut driver to tighten the standoffs.

Caution

Make sure that the standoffs are straight when installed. Tighten them gently but firmly. The shoulder 
of each standoff must be seated tightly against the system board.

Step 3

Place the inline power supply card on top of the three metal standoffs, lining up the metal standoffs with 
the screw holes in the inline power supply card.

Step 4

Insert the screws provided in the accessory kit through the inline power supply card and into the metal 
standoffs. Carefully tighten the screws with a Phillips screwdriver.

After you install the inline power supply card in the router, install the router cover and connect the inline 
power supply to the power connector on the back of the router.

Installing the Chassis Cover

The Cisco 1800 series fixed-configuration router has a cover that slides onto the chassis from the back 
of the chassis. Follow these steps to install the chassis cover on a Cisco 1800 series fixed-configuration 
router:

Step 1

Gently slide the cover of the router onto the chassis.

Step 2

Replace the cover screw that you removed when you opened the chassis. See the 

“Removing the Chassis 

Cover” section on page 7-2

.

Summary of Contents for 1800 Series



















































































Reviews:

No comments