Cisco 10008 Installation And Configuration Manual Download Page 62

Page: 62 / 70

Cisco 10008 Router PRE4 Installation and Configuration Guide

OL-13840-01

show pxf dma

To display the current state of direct memory access (DMA) buffers, error counters, and registers on the
Parallel eXpress Forwarding (PXF) engine, use the

show pxf dma

command in privileged EXEC mode.

show pxf dma

[

buffers

counters

reassembly

registers

]

Cisco 10000 Series Router (PRE3 and PRE4)

show pxf dma

[

buffers

counters

reassembly

registers

] [

brief

config

errors

status

]

Syntax Description

Command Modes

Privileged EXEC

Command History

buffers

(Optional) Displays PXF DMA buffers information.

counters

(Optional) Displays packet and error counters for the PXF DMA engine.

reassembly

(Optional) Displays PXF reassembly table usage information.

registers

(Optional) Displays PXF DMA registers information.

brief

(Optional) Displays PXF DMA information, including the initialization state
of each block in the PXF API and any errors that occurred.

Note

This option is only available on the Cisco 10000 series router for the
PRE3 and PRE4.

config

(Optional) Displays a configuration summary of the registers in each of the
PXF DMA blocks.

Note

This option is only available on the Cisco 10000 series router for the
PRE3 and PRE4.

errors

(Optional) Displays the errors that occurred in each of the PXF DMA blocks.

Note

This option is only available on the Cisco 10000 series router for the
PRE3 and PRE4.

status

(Optional) Displays the initialization state of each PXF DMA block. In
normal operation, all blocks display the enabled state.

Note

This option is only available on the Cisco 10000 series router for the
PRE3 and PRE4.

Release

Modification

12.2S

This command was introduced.

12.3(7)XI

This command was integrated into Cisco IOS Release 12.3(7)XI and
implemented on the Cisco 10000 series router for the PRE2.

12.2(31)SB2

This command was integrated into Cisco IOS Release 12.2(31)SB2 and
implemented on the Cisco 10000 series router for the PRE3.

12.2(33)SB

This command was introduced on the PRE4 for the Cisco 10000 series
router.

Summary of Contents for 10008







































































Search results

Summary of Contents for 10008

Reviews:

Cisco 10008, Installation And Configuration Manual, Page: 62 / 70

Search results

Summary of Contents for 10008

Reviews: