background image

VCC-2CXP6M 

                                                                                                                           

Rev.905-0186-02 

©2019 CIS Corporation. All rights reserved. 

28 

 

6.

 

Factory Settings 

Function 

Data 

Description 

TriggerSelector 

AcquisitionStart 

Equivalent to TriggerMode=Off 

TriggerMode 

Off 

Link to TriggerSelector 

TriggerSyncMode 

LineSync 

Horizontal sync. mode 

TriggerSource 

LinkTrigger0 

CXP UPLink trigger 

TriggerActivation 

RisingEdge 

Rising edge 

ExposureTime 

7938.0 

7.938ms

 

Gain 

1.00 

x1.00 

Gamma 

1.00 

Gamma coefficient=1.00 

 

 

 

DefectPixelCorrection 

On 

Defective pixels correction On

 

DefectPixelAddOffsetX 

This is to specify X coordinate to correct 
defective pixels. 

DefectPixelAddOffsetY 

This is to specify Y coordinate to correct 
defective pixels. 

DefectDetectionThesholdValue 

50 

Defective pixels detection threshold value 

 

 

 

BlackOffset 

Black level initial value 

 

 

 

PixelFormat 

Mono8 

B/W model

 

 

 

 

ConnectionConfig 

CXP3_X1 

CxpLinkConfiguration 

TestMode

 

NomalOperation 

Link test Off 

 

 

 

RegionSelector 

EffectiveRegion 

This  is  to  specify  the  number  of  Partial 
area (ROI) (Region1) 

RegionMode 

On 

Partial area (ROI) On/Off 

Height 

1248 

Partial area (ROI) Specify height. 

OffsetY 

Partial  area  (ROI)  Specify  the  start 
position. 

 

 

 

TestPattern 

Off 

Cursor indication and Test pattern cannot 
be ON at the same time. 

CursorPattern 

Off 

Test pattern and Cursor pattern cannot   
be ON at the same time. 

CursorOffsetX 

816 

This is to specify the position of cursor X 

CursorOffsetY 

623 

This is to specify the position of cursor Y 

CursorColor 

White 

Cursor color

 

White/Black 

 

 

 

BiningHorizontal 

2x2 binning mode 

BiningVertical 

2x2 binning mode 

 

 

 

 

 

 

DeviceIndicatorMode 

Active 

Indicate LED indicator 

LineSource 

Off 

Circular 6P-3pin output settings 

DeviceUserID 

 

User letter string setting (16 letters) 

         

 

Summary of Contents for VCC-2CXP6M



































Reviews: