Cirrus Logic CRD5378 Manual Download

Page: 8 / 64

CRD5378

DS639RD2

1.3

Software Setup

1.3.1

PC Requirements

The PC hardware requirements for the Cirrus Seismic Evaluation system are:

• Windows XP

, Windows 2000™, Windows NT

• Intel Pentium 600 MHz or higher microprocessor

• VGA resolution or higher video card

• Minimum 64MB RAM

• Minimum 40MB free hard drive space

1.3.2

Seismic Evaluation Software Installation

Important:

For reliable USB communication, the USBXpress

driver must be installed after the Seismic

Evaluation Software installation but

before

launching the application. The USBXpress driver files are in-

cluded in a sub-folder as part of the installation.

To install the Cirrus Logic Seismic Evaluation Software:

• Go to the Cirrus Logic Industrial Software web page (

http://www.cirrus.com/industrialsoftware

). Click

the link for

“Cirrus Seismic Evaluation GUI”

to get to the download page and then click the link for

“Cir-

rus Seismic Evaluation GUI Release Vxx”

(

indicates the version number).

• Read the software license terms and click

“Accept”

to download the

“SeismicEvalGUI_vxx.zip”

file to

any directory on the PC.

• Unzip the downloaded file to any directory and a

“Distribution\Volume1”

sub-folder containing the in-

stallation application will automatically be created.

• Open the

“Volume1”

sub-folder and run

“setup.exe”

. If the Seismic Evaluation Software has been pre-

viously installed, the uninstall wizard will automatically remove the previous version during install.

• Follow the instructions presented by the Cirrus Seismic Evaluation Installation Wizard. The default in-

stallation location is

“C:\Program Files\Cirrus Seismic Evaluation”

An application note,

AN271 -

Cirrus Seismic Evaluation GUI Installation Guide

, is available from the Cirrus

Logic web site with step-by-step instructions on installing the Seismic Evaluation Software.

1.3.3

USBXpress

Driver Installation

Important:

For reliable USB communication, the USBXpress

driver must be installed after the Seismic

Evaluation Software installation but

before

launching the application. The USBXpress driver files are in-

cluded in a sub-folder as part of the installation.

The Cirrus Logic Seismic Evaluation Software communicates with CRD5378 via USB using the USBX-
press driver from Silicon Laboratories (

http://www.silabs.com

). For convenience, the USBXpress driver

files are included as part of the installation package.

To install the USBXpress driver (after installing the Seismic Evaluation Software):

• Connect CRD5378 to the PC through an available USB port and apply power. The PC will detect

CRD5378 as an unknown USB device.

Summary of Contents for CRD5378

































































Search results

Summary of Contents for CRD5378

Reviews:

Related manuals for CRD5378

Brands by name

Popular brands

Cirrus Logic CRD5378, Manual

Search results

Summary of Contents for CRD5378

Reviews:

Related manuals for CRD5378

Brands by name

Popular brands