Cirrus Logic CDB5378 Manual Download

Page: 11 / 75

CDB5378

DS639DB4

1.3

Software Setup

1.3.1

PC Requirements

The PC hardware requirements for the Cirrus Seismic Evaluation system are:

• Windows XP, Windows 2000, Windows NT

• Intel Pentium 600MHz or higher microprocessor

• VGA resolution or higher video card

• Minimum 64MB RAM

• Minimum 40MB free hard drive space

1.3.2

Seismic Evaluation Software Installation

Important:

For reliable USB communication, the USBXpress driver must be installed after the Seismic

Evaluation Software installation but

before

launching the application. The USBXpress driver files are in-

cluded in a sub-folder as part of the installation.

To install the Cirrus Logic Seismic Evaluation Software:

• Go to the Cirrus Logic Industrial Software web page (

http://www.cirrus.com/industrialsoftware

). Click

the link for

“Cirrus Seismic Evaluation GUI”

to get to the download page and then click the link for

“Cir-

rus Seismic Evaluation GUI Release Vxx”

(

indicates the version number).

• Read the software license terms and click

“Accept”

to download the

“SeismicEvalGUI_vxx.zip”

file to

any directory on the PC.

• Unzip the downloaded file to any directory and a

“Distribution\Volume1”

sub-folder containing the in-

stallation application will automatically be created.

• Open the

“Volume1”

sub-folder and run

“setup.exe”

. If the Seismic Evaluation Software has been pre-

viously installed, the uninstall wizard will automatically remove the previous version and you will need
to run

“setup.exe”

again.

• Follow the instructions presented by the Cirrus Seismic Evaluation Installation Wizard. The default in-

stallation location is

“C:\Program Files\Cirrus Seismic Evaluation”

An application note, AN271 -

Cirrus Seismic Evaluation GUI Installation Guide

, is available from the Cirrus

Logic web site with step-by-step instructions on installing the Seismic Evaluation Software.

1.3.3

USBXpress Driver Installation

Important:

For reliable USB communication, the USBXpress driver must be installed after the Seismic

Evaluation Software installation but

before

launching the application. The USBXpress driver files are in-

cluded in a sub-folder as part of the installation.

The Cirrus Logic Seismic Evaluation Software communicates with CDB5378 via USB using the USBX-
press driver from Silicon Laboratories (

http://www.silabs.com

). For convenience, the USBXpress driver

files are included as part of the installation package.

To install the USBXpress driver (after installing the Seismic Evaluation Software):

• Connect CDB5378 to the PC through an available USB port and apply power. The PC will detect

Summary of Contents for CDB5378












































































Search results

Summary of Contents for CDB5378

Reviews:

Related manuals for CDB5378

Brands by name

Popular brands

Cirrus Logic CDB5378, Manual

Search results

Summary of Contents for CDB5378

Reviews:

Related manuals for CDB5378

Brands by name

Popular brands