Cincoze CO-100/P2102 Series User Manual Download

Page: 21 / 102

100/P2102

Series | User Manual

1.5.3 Left

Antenna

Used to connect an antenna for optional wireless

WIFI module

USB 2.0

Used to connect to USB 2.0/1.1 compatible
devices

COM1, COM2

Used to connect to RS-232/422/485 serial devices

1.5.4 Right

COM3, COM4

Used to connect to RS-232/422/485 serial

devices

USB3.2 Gen2

Used to connect to USB 3.2 Gen2/3.2

Gen1/2.0/1.1 compatible devices

Line-Out

Used to connect a speaker

Mic-In

Used to connect a microphone

OSD Function (For CDS Display Module)

LCD On/Off

Press to turn-on or turn-off the backlight of

display

Increase Brightness

Press to increase brightness of the screen

Decrease Brightness

Press to decrease brightness of the screen

Summary of Contents for CO-100/P2102 Series







































































































Search results

Summary of Contents for CO-100/P2102 Series

Reviews:

Related manuals for CO-100/P2102 Series

Brands by name

Popular brands

Cincoze CO-100/P2102 Series, User Manual

Search results

Summary of Contents for CO-100/P2102 Series

Reviews:

Related manuals for CO-100/P2102 Series

Brands by name

Popular brands