I
nstallation/
U
ser
Manual
for
the
Chunc
Docking
I
nterface
for
Q
Straint
Q
L
K
-
100/150
Keep chair positioned on its back.
Insert the leg rest brace bar into the chunc interface
and refit into the upper frame ensuring it is
orientated correctly.
Secure in position by attaching the rear chassis cross
bar supplied with the interface.
Note:
The labels
on the rear chassis cross bar should be facing the rear
of the chair when fitting.
Position chair back into a horizontal position.
Add a small amount of thread locking adhesive to
both threads of the gas strut. Attach bottom first and
tighten securely by hand.
Replace
wheels.
Set
tilt
angle
for
trans
p
ortation:
Adjust the tilt in space so that the bottom edge of
chunc interface is parallel with the ground. Adjust
and secure the linkages to the required tilt angle for
transportation. There is approx 4 degrees between
settings.
!
Where possible, the seat (tilt in space) should be set
to a near horizontal position with a slight rearward
bias (similar to normal vehicle seat).
Secure the docking bolt (supplied with QLK) to the
chunc interface in accordance with the QLK system
for chunc installation manual and verify/adjust the
seated angle for transportation when engaged in
an installed QLK following the
directions
for
usage
instructions.
Posture
and
mobility
for
young
p
eo
p
le
Directions
for
Fitting
Part
-
2
I
nstructions
Photos
BS
E
N
I
SO
9001:2000
4
1
4
6
3
2
www.chunc.com
1
2
3
4
5
6
7
8
a
a
a
b
b
Chunc Wheelchairs
Specmat Limited
Tarsmill Court
Rotherwas
Hereford, HR2 6JZ, UK
t. +44(0) 1432 377512
f. +44(0) 1432 377516
e. [email protected]
The Chunc range of wheelchairs an accessories are designed and manufactured to meet the requirements of the Medical Devices Directive 3/42/EEC for Class 1 medical devices. Specmat
Limited holds the British Standard Quality Approval to BS EN ISO 9001:2000 for design and manufacture of medical devices. All products FDA approved: site registration number 3004709721.
Patents pending include EP 03251925, Design Registration includes USD 5952, EC 000080627. Granted Patent U.S. 6,994,364. Chunc is a trademark of Specmat Ltd, part of the HR Smith Group of
Companies. © Copyright Specmat Ltd 2007. All rights reserved. All technical information is subject to alteration without notice.
T
HIS
USER
MANUAL
IS
AVAILABLE
IN
LARGE
PRIN
T
FOR
PRODUC
T
WARRAN
TY
,
PLEASE
SEE
CHUNC
USER
MANUAL
: c
hun
c
.
c
om
Installation/User Manual for the Chunc Docking Interface for Q Straint QLK-100/150 Issue 2, C/N 5794, September 2011. Document No. HRS 1146-07-10
7
I
nstallation/
U
ser
Manual
for
the
Chunc
Docking
I
nterface
for
Q
Straint
Q
L
K
-
100/150
!
Please make sure you have completed and checked
the
directions
for
fi
tting
before using this manual.
Tilt the wheelchair to avoid the footrests catching on
the QLK.
Push the wheelchair over the QLK so the footrests are
just clear of it.
Tilt the Chunc forward so the bottom edge of the
Chunc interface bracket is parallel with the QLK and
the docking bolt is aligned.
Push home the Chunc engaging the bolt into the lock
and the stabilising lugs underneath the back edge of
the QLK.
Tilt the wheelchair back and release the foot lever,
leaving the chair in tension in the QLK. This removes
any play and will hold the chair firm.
Fasten seat belt ensuring the seat belt is positioned
through the seating components and armrests
to interface correctly across occupants hips and
shoulder.
Note:
Only to be used with a three point
vehicle mounted lap and shoulder seat belt.
Note:
You will need to tilt the chair slightly forward to
the parallel position prior to releasing from the QLK.
For instruction on releasing the chair from the
QLK please refer to the
Q
LK-
1
00
system
for
c
hun
c
insta
ll
ation/operators
manua
l
.
Posture
and
mobility
for
young
p
eo
p
le
Directions
for
usage
I
nstructions
Photos
BS
E
N
I
SO
9001:2000
1
4
2
5
3
6
www.chunc.com
1
2
3
4
5
6
7
Chunc Wheelchairs
Specmat Limited
Tarsmill Court
Rotherwas
Hereford, HR2 6JZ, UK
t. +44(0) 1432 377512
f. +44(0) 1432 377516
e. [email protected]
The Chunc range of wheelchairs an accessories are designed and manufactured to meet the requirements of the Medical Devices Directive 3/42/EEC for Class 1 medical devices. Specmat
Limited holds the British Standard Quality Approval to BS EN ISO 9001:2000 for design and manufacture of medical devices. All products FDA approved: site registration number 3004709721.
Patents pending include EP 03251925, Design Registration includes USD 5952, EC 000080627. Granted Patent U.S. 6,994,364. Chunc is a trademark of Specmat Ltd, part of the HR Smith Group of
Companies. © Copyright Specmat Ltd 2007. All rights reserved. All technical information is subject to alteration without notice.
T
HIS
USER
MANUAL
IS
AVAILABLE
IN
LARGE
PRIN
T
FOR
PRODUC
T
WARRAN
TY
,
PLEASE
SEE
CHUNC
USER
MANUAL
: c
hun
c
.
c
om
Installation/User Manual for the Chunc Docking Interface for Q Straint QLK-100/150 Issue 2, C/N 5794, September 2011. Document No. HRS 1146-07-10
For
fu
ll
guidan
c
e
p
l
ease
see
the
safe
transportation
se
c
tion
in
the
c
hun
c
user
manua
l
and
Q
LK-
1
00/
1
50
system
for
c
hun
c
insta
ll
ation/operators
manua
l
a
v
ai
l
ab
l
e
from
www.
c
hun
c
.
c
om
Please Note
Crash Tested to 10542-5
8
