manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 95 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 95

Power Mirrors — If Equipped

The power mirror controls are located on the driver-side
door trim panel.

The power mirror controls consist of mirror select buttons
and a four-way mirror control switch. To adjust a mirror,
push either the L (left) or R (right) to select the mirror that
you want to adjust.

NOTE:

A light in the selected button will illuminate

indicating the mirror is activated and can be adjusted.

Using the mirror control switch, push on any of the four
arrows for the direction that you want the mirror to move.

Outside Mirrors Folding Feature

All outside mirrors are hinged and may be moved either
forward or rearward to resist damage. The hinges have
three detent positions:

•

Full forward position

•

Full rearward position

•

Normal position

Heated Mirrors — If Equipped

These mirrors are heated to melt frost or ice. This
feature will be activated whenever you turn on the

rear window defroster (if equipped). Refer to “Climate
Controls” for further information.

Power Mirror Controls

3

GETTING TO KNOW YOUR VEHICLE

93

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments