Home
/
Chrysler
/
Pacifica Hybrid 2018
/
Owner'S Manual

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 94 / 617

Share

Page: 94 / 617

Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 94

Outside Mirrors

To receive maximum benefit, adjust the outside mirror(s) to
center on the adjacent lane of traffic with a slight overlap of
the view obtained on the inside mirror.

WARNING!

Vehicles and other objects seen in an outside convex
mirror will look smaller and farther away than they
really are. Relying too much on side convex mirrors
could cause you to collide with another vehicle or other
object. Use your inside mirror when judging the size or
distance of a vehicle seen in a side convex mirror.

Driver’s Outside Automatic Dimming Mirror — If
Equipped

The driver’s outside mirror will automatically adjust for
glare from vehicles behind you. This feature is controlled
by the inside automatic dimming mirror and will automati-
cally adjust for headlight glare when the inside mirror
adjusts.

Conversation Mirror

Located in the overhead console there is a conversation
mirror to view all the passengers in the vehicle. Push the
panel to release the drop down mirror. Raise the mirror and
push to latch it back in the stowed position.

Conversation Mirror

92

GETTING TO KNOW YOUR VEHICLE

«
...
92
93
94
95
96
...
»

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments