manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 346 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 346

show a

⬙

PARKSENSE UNAVAILABLE WIPE REAR SEN-

SORS

⬙

,

⬙

PARKSENSE UNAVAILABLE WIPE FRONT SEN-

SORS

⬙

or

⬙

PARKSENSE UNAVAILABLE SERVICE RE-

QUIRED

⬙

pop up message for five seconds. After five

seconds, a vehicle graphic will be displayed with

⬙

OFF

⬙

at

either the front or rear sensor location depending on where
the fault is detected. The system will continue to provide
arc alerts for the side that is functioning properly. These arc
alerts will interrupt the

⬙

PARKSENSE UNAVAILABLE

WIPE REAR SENSORS

⬙

,

⬙

PARKSENSE UNAVAILABLE

WIPE FRONT SENSORS

⬙

, or

⬙

PARKSENSE UNAVAIL-

ABLE SERVICE REQUIRED

⬙

messages if an object is

detected within the five second pop-up duration. The
vehicle graphic will remain displayed for as long as the
vehicle is in REVERSE.

Refer to “Instrument Cluster Display” in “Getting To Know
Your Instrument Panel” for further information.

If

⬙

PARKSENSE UNAVAILABLE WIPE REAR SENSORS

⬙

or

⬙

PARKSENSE UNAVAILABLE WIPE FRONT SEN-

SORS

⬙

appears in the instrument cluster display make sure

the outer surface and the underside of the rear fascia/
bumper and/or front fascia/bumper is clean and clear of
snow, ice, mud, dirt or other obstruction and then cycle the
ignition. If the message continues to appear see an autho-
rized dealer.

If the

⬙

PARKSENSE UNAVAILABLE SERVICE RE-

QUIRED

⬙

message appears in the instrument cluster dis-

play, see an authorized dealer.

Cleaning The ParkSense System

Clean the ParkSense sensors with water, car wash soap and
a soft cloth. Do not use rough or hard cloths. Do not scratch
or poke the sensors. Otherwise, you could damage the
sensors.

ParkSense System Usage Precautions

NOTE:

•

Ensure that the front and rear bumper are free of snow,
ice, mud, dirt and debris to keep the ParkSense system
operating properly.

•

Construction equipment, large trucks, and other vibra-
tions could affect the performance of ParkSense.

•

When you turn ParkSense off, the instrument cluster
will display “PARKSENSE OFF.” Furthermore, once you
turn ParkSense off, it remains off until you turn it on
again, even if you cycle the ignition key.

344

STARTING AND OPERATING

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments