manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 306 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 306

Adaptive Cruise Control (ACC) Operation

The speed control buttons (located on the right side of the
steering wheel) operates the ACC system.

NOTE:

Any chassis/suspension or tire size modifications

to the vehicle will effect the performance of the Adaptive
Cruise Control and Forward Collision Warning System.

Activating Adaptive Cruise Control (ACC)

You can only engage ACC if the vehicle speed is above
0 mph (0 km/h).

The minimum Set Speed for the ACC system is 20 mph
(32 km/h).

When the system is turned on and in the READY state, the
instrument cluster displays “ACC Ready.”

When the system is OFF, the instrument cluster display
“Adaptive Cruise Control (ACC) Off.”

NOTE:

You cannot engage ACC under the following con-

ditions:

•

When you apply the brakes.

•

When the parking brake is applied.

•

When the automatic transmission is in PARK, REVERSE
or NEUTRAL.

•

When the vehicle speed is outside of the speed range.

•

When the brakes are overheated.

Adaptive Cruise Control Buttons

1 — Normal (Fixed Speed) Cruise Control On/Off
2 — SET+/Accel
3 — RES/Resume
4 — SET-/Decel
5 — Distance Setting Increase
6 — Adaptive Cruise Control (ACC) On/Off
7 — Distance Setting Decrease
8 — CANC/Cancel

304

STARTING AND OPERATING

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments