manualshive.com logo in svg

Chrysler Pacifica Hybrid 2018, Owner'S Manual, Page: 286 / 617

Share
Download
Chrysler Pacifica Hybrid 2018 Owner'S Manual Download Page 286

STARTING THE ENGINE

Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belts.

WARNING!

•

When exiting the vehicle, always remove the key fob
from the vehicle and lock your vehicle.

•

Never leave children alone in a vehicle, or with
access to an unlocked vehicle.

•

Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or others
could be seriously or fatally injured. Children
should be warned not to touch the parking brake,
brake pedal or the transmission gear selector.

•

Do not leave the key fob in or near the vehicle, or in
a location accessible to children, and do not leave the
ignition of a vehicle equipped with Keyless Enter-
N-Go in the ACC or ON/RUN mode. A child could
operate power windows, other controls, or move the
vehicle.

•

Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.

Start the engine with the gear selector in the PARK
position. Apply the brake before shifting to any driving
range.

NOTE:

In case the ignition switch does not change with the

push of a button, the key fob may have a low or dead
battery. In this situation, a back up method can be used to
operate the ignition switch. Put the nose side of the key fob
(side opposite of the Emergency Key) against the ENGINE
START/STOP button and push to operate the ignition
switch.

Normal Starting

NOTE:

Normal starting of either a cold or a warm engine

is obtained without pumping or pressing the accelerator
pedal.

To Turn On The Vehicle Using ENGINE START/STOP
Button

1. The transmission must be in PARK or NEUTRAL.

2. Press and hold the brake pedal while pushing the

ENGINE START/STOP button once.

3. The vehicle will go into Drive Ready mode (silent start,

and “ready” is indicated on the cluster without the

284

STARTING AND OPERATING

Summary of Contents for Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Reviews:

No comments