Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 71 | Manualshive

Page: 71 / 604

background image

WARNING!

•

Adjusting a seat while driving may be dangerous.
Moving a seat while driving could result in loss of
control which could cause a collision and serious
injury or death.

•

Seats should be adjusted before fastening the seat belts
and while the vehicle is parked. Serious injury or death
could result from a poorly adjusted seat belt.

Manual Reclining Seats — If Equipped

For models equipped with manual seats, the recline lever is
located on the outboard side of the seat.

To recline, lean forward slightly, lift the lever and push
back to the desired position and release the lever. Lean
forward and lift the lever to return the seatback to its
normal position. Using body pressure, lean forward and
rearward on the seat to be sure the seatback has latched.

WARNING!

Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest. In
a collision you could slide under the seat belt, which
could result in serious injury or death.

Manual Recline Lever

3

GETTING TO KNOW YOUR VEHICLE

69

«
...
69
70
71
72
73
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Acdeos Pages: 38

Brand: Federal Signal Corporation Pages: 8

Brand: Federal Signal Corporation Pages: 8

Brand: Dodge Pages: 24

2014 Grand Cherokee SRT8

Brand: Jeep Pages: 596

Brand: Skoda Pages: 4

Electra 225 1965

Brand: Buick Pages: 914

Brand: Kia Pages: 11

Brand: Saab Pages: 426

Brand: Pontiac Pages: 20

1500 CLASSIC 2020

Brand: RAM Pages: 360

Brand: Kolpin Pages: 6

Brand: MacNeil Pages: 2

Brand: EUFAB Pages: 18

Brand: ROLEC Pages: 2

viano 639 series

Brand: Mercedes-Benz Pages: 32

Brand: Toyota Pages: 18

Brand: JCROffroad Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands