Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 70 | Manualshive

Page: 70 / 604

background image

WARNING!

(Continued)

these areas are more likely to be seriously injured or
killed.

•

Do not allow people to ride in any area of your
vehicle that is not equipped with seats and seat belts.
In a collision, people riding in these areas are more
likely to be seriously injured or killed.

•

Be sure everyone in your vehicle is in a seat and
using a seat belt properly.

Manual Adjustment (Front Seats)

WARNING!

•

Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat could
cause you to lose control. The seat belt might not be
adjusted properly and you could be injured. Adjust
the seat only while the vehicle is parked.

•

Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest.
In a collision you could slide under the seat belt and
be seriously or even fatally injured. Use the recliner
only when the vehicle is parked.

Manual Front Adjuster

Both front seats are adjustable forward or rearward. The
manual seat adjustment handle is located under the seat
cushion at the front edge of each seat.

While sitting in the seat, pull up on the handle and slide the
seat forward or rearward. Release the bar once you have
reached the desired position. Then, using body pressure,
move forward and rearward on the seat to be sure that the
seat adjusters have latched.

Manual Seat Adjuster

68

GETTING TO KNOW YOUR VEHICLE

«
...
68
69
70
71
72
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Camcar Pages: 2

Brand: Kargo Master Pages: 5

Brand: J-Top Pages: 2

Brand: HALE Pages: 44

FleetMaster Air FW8 Series

Brand: SAF-HOLLAND Pages: 20

Brand: Cequent Pages: 9

Brand: hc-cargo Pages: 60

Brand: Metra Electronics Pages: 20

Brand: RAM Pages: 76

Brand: Advantech Pages: 59

Brand: Jeep Pages: 136

Brand: RAM Pages: 148

Brand: Hamron Pages: 36

Brand: Axxess Pages: 8

Brand: Whispbar Pages: 18

Brand: Chevrolet Pages: 103

Brand: Peak Pages: 8

Brand: Renault Pages: 239

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands