manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

CAUTION!

Be sure to mount the tire with the valve stem facing
outward. The vehicle could be damaged if the inflat-
able spare tire is mounted incorrectly.

7. Secure the wheel to the hub by tightening the nuts with

wrench. Once the vehicle is lowered you will have a
second opportunity to “torque” the lug nuts.

8. Finish tightening the lug nuts. Push down on the

wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each

nut has been tightened twice. Refer to “Torque Specifi-
cations” in “Technical Specifications” for proper wheel
lug nut torque. If in doubt about the correct tightness,
have them checked with a torque wrench by your
authorized dealer or at a service station.

9. Lower the jack to its fully lowered position.

WARNING!

A loose tire or jack thrown forward in a collision or
hard stop could endanger the occupants of the vehicle.
Always stow the jack parts and the spare tire in the
places provided. Have the deflated (flat) tire repaired
or replaced immediately.

Road Tire Installation

Vehicles Equipped With Wheel Covers

1. Mount the road tire on the axle.

2. To ease the installation process for steel wheels with

wheel covers, install two lug nuts on the mounting
studs which are on each side of the valve stem. Install
the lug nuts with the cone shaped end of the nut toward
the wheel. Lightly tighten the lug nuts.

Installing Tire

412

IN CASE OF EMERGENCY

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

ULTIMATE SPEED CARBON Assembly And Safety Advice preview
CARBON
Brand: ULTIMATE SPEED Pages: 19
RAM 2015 1500 User Manual preview
2015 1500
Brand: RAM Pages: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Brand: RAM Pages: 116
Rago FABRICATION R2223TTUNDM Installation Manual preview
R2223TTUNDM
Brand: Rago FABRICATION Pages: 10
Sears 580.32601 Owner'S Manual preview
580.32601
Brand: Sears Pages: 41
Kia 2014 rondo Features preview
2014 rondo
Brand: Kia Pages: 11
Saab 2008 9-7x Owner'S Manual preview
2008 9-7x
Brand: Saab Pages: 426
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Brand: Cadillac Pages: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Brand: Fortin Pages: 9
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Brand: Thule Pages: 12
RAM RAM C 2013 Specification preview
RAM C 2013
Brand: RAM Pages: 5
EUFAB 12014 Manual preview
12014
Brand: EUFAB Pages: 20
Pet Gear TL9000 Instruction Manual preview
TL9000
Brand: Pet Gear Pages: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Brand: Suzuki Pages: 570
Dhollandia DH-RB 05.02 Series User Manual preview
DH-RB 05.02 Series
Brand: Dhollandia Pages: 65
Menabo ANTARES KIT+1 Assembly & Instruction Manual preview
ANTARES KIT+1
Brand: Menabo Pages: 8
Seat Arona 2018 Owner'S Manual preview
Arona 2018
Brand: Seat Pages: 372
FIRRAK FIRRAK arca Assembly Instructions Manual preview
FIRRAK arca
Brand: FIRRAK Pages: 12

Brands by name

Popular brands

Load more brands