manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

JACKING AND TIRE CHANGING

NOTE:

Your vehicle is not equipped with a jack or spare

tire. This section describes wheel removal and installation.

WARNING!

•

Do not attempt to change a tire on the side of the
vehicle close to moving traffic. Pull far enough off
the road to avoid the danger of being hit when
operating the jack or changing the wheel.

•

Being under a jacked-up vehicle is dangerous. The
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
under a vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service center
where it can be raised on a lift.

•

The jack is designed to be used as a tool for changing
tires only. The jack should not be used to lift the
vehicle for service purposes. The vehicle should be
jacked on a firm level surface only. Avoid ice or
slippery areas.

Preparations For Jacking

1. Park the vehicle on a firm, level surface. Avoid ice or

slippery areas.

WARNING!

Do not attempt to change a tire on the side of the
vehicle close to moving traffic, pull far enough off the
road to avoid being hit when operating the jack or
changing the wheel.

2. Turn on the Hazard Warning flasher.

3. Set the parking brake.

4. Place the gear selector into PARK.

5. Turn OFF the ignition.

6. Block both the front and rear of the wheel diagonally

opposite of the jacking position. For example, if chang-
ing the right front tire, block the left rear wheel.

NOTE:

Passengers should not remain in the

vehicle when the vehicle is being jacked.

7

IN CASE OF EMERGENCY

407

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Wagan 2591 User Manual preview
2591
Brand: Wagan Pages: 12
RACLET SAFARI Setup And Maintenance Manual preview
SAFARI
Brand: RACLET Pages: 48
RACLET Allegra Manual preview
Allegra
Brand: RACLET Pages: 31
TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Brand: TATA Motors Pages: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Brand: TAUBENREUTHER Pages: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Brand: Yakima Pages: 15
Ford E-Transit 2022 Manual preview
E-Transit 2022
Brand: Ford Pages: 22
Porsche 01-B Web Application Manual preview
01-B
Brand: Porsche Pages: 313
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Brand: Lit Lightz Pages: 3
Westfalia 305 158 Mounting Instructions preview
305 158
Brand: Westfalia Pages: 10
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Brand: Mobility Networks Pages: 52
Skoda Superb 2006 Owner'S Manual preview
Superb 2006
Brand: Skoda Pages: 281
Cadillac 1999 Escalade Owner'S Manual preview
1999 Escalade
Brand: Cadillac Pages: 352
BMW 84 61 0 028 926 Installation Instructions Manual preview
84 61 0 028 926
Brand: BMW Pages: 13
Roadtrek SS Agile 2017 Owner'S Manual preview
SS Agile 2017
Brand: Roadtrek Pages: 61
Whispbar K481W Fitting Instructions Manual preview
K481W
Brand: Whispbar Pages: 14
OMNISTOR Omni-Bike Sport Ducato Installation preview
Omni-Bike Sport Ducato
Brand: OMNISTOR Pages: 5
Westin 28-21030 Instructions preview
28-21030
Brand: Westin Pages: 3

Brands by name

Popular brands

Load more brands