manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

The system will also continuously perform the dynamic
vehicle calibration to account for differences such as
over or under inflated tires and new tires.

Enabling And Disabling The ParkSense Active Park
Assist System

The ParkSense Active Park Assist system can be enabled
and disabled with the ParkSense Active Park Assist switch,
located on the switch panel below the Uconnect display.

To enable the ParkSense Active Park Assist system, push
the ParkSense Active Park Assist switch once (LED turns
on).

To disable the ParkSense Active Park Assist system, push
the ParkSense Active Park Assist switch again (LED turns
off).

The ParkSense Active Park Assist system will turn off
automatically for any of the following conditions:

•

The parking maneuver is completed.

•

Vehicle speed greater than 18 mph (30 km/h) when
searching for a parking space.

•

Vehicle speed greater than 5 mph (7 km/h) during active
steering guidance into the parking space.

•

Touching the steering wheel during active steering guid-
ance into the parking space.

•

Pushing the ParkSense Front and Rear Park Assist
switch.

•

The Driver’s door is opened.

•

The liftgate is opened.

•

Electronic Stability Control/Anti-lock Braking System
intervention.

•

The ParkSense Active Park Assist system will allow a
maximum of six shifts between DRIVE and REVERSE. If
the maneuver cannot be completed within six shifts, the

ParkSense Active Park Assist Switch

346

STARTING AND OPERATING

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

PAC I GM3 Instruction Manual preview
I GM3
Brand: PAC Pages: 15
Daihatsu Mira Manual preview
Mira
Brand: Daihatsu Pages: 340
RaceChip Pro 2 Installation Manual preview
Pro 2
Brand: RaceChip Pages: 12
Laser 4832 Manual preview
4832
Brand: Laser Pages: 8
Whispbar K783W Fitting Instructions Manual preview
K783W
Brand: Whispbar Pages: 16
BMW Wireless Charging Station Universal Instructions For Use Manual preview
Wireless Charging Station Universal
Brand: BMW Pages: 160
Parrot Parrot MKi + ParrotCK3100 range LOGAN Installation Manual preview
Parrot MKi + ParrotCK3100 range LOGAN
Brand: Parrot Pages: 10
Kia Bluetooth Phone System 2010 Reference Manual preview
Bluetooth Phone System 2010
Brand: Kia Pages: 16
Mitsubishi Fuso FK 2010 Owner'S Manual preview
Fuso FK 2010
Brand: Mitsubishi Pages: 362
Waeco MagicSafe MSG150 Installation And Operating Manua preview
MagicSafe MSG150
Brand: Waeco Pages: 20
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Brand: Acura Pages: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Brand: Ford Pages: 325
Volvo XC60 2009 Owner'S Manual preview
XC60 2009
Brand: Volvo Pages: 304
Acewell CA-085-15X User Manual preview
CA-085-15X
Brand: Acewell Pages: 7
hager XEV1R22T2 Series Operating Instructions Manual preview
XEV1R22T2 Series
Brand: hager Pages: 14
WALMEC 40087 Mounting Instructions preview
40087
Brand: WALMEC Pages: 6
Laser NAVC-BHUD-982 User Manual preview
NAVC-BHUD-982
Brand: Laser Pages: 23
ikross IKHD74 User Manual preview
IKHD74
Brand: ikross Pages: 2

Brands by name

Popular brands

Load more brands