Chrysler pacifica hybrid 2017 Owner'S Manual Download Page 212 | Manualshive

Page: 212 / 604

background image

General Information

This vehicle has systems that operate on radio frequency
that comply with Part 15 of the Federal Communications
Commission (FCC) rules and with Industry Canada Stan-
dards RSS- GEN/210/220/310.

Operation is subject to the following two conditions:

1. The device may not cause harmful interference.

2. The device must accept any interference received, in-

cluding interference that may cause undesired operation
of the device.

Changes or modifications to any of these systems by other
than an authorized service facility could void authorization
to use this equipment.

Forward Collision Warning (FCW) With Mitigation
— If Equipped

The Forward Collision Warning (FCW) system with miti-
gation provides the driver with audible warnings, visual
warnings (within the instrument cluster display), and may
apply a brake jerk to warn the driver when it detects a
potential frontal collision. The warnings and limited brak-
ing are intended to provide the driver with enough time to
react, avoid or mitigate the potential collision.

NOTE:

FCW monitors the information from the forward

looking sensors as well as the Electronic Brake Controller
(EBC), to calculate the probability of a forward collision.
When the system determines that a forward collision is
probable, the driver will be provided with audible and
visual warnings and may provide a brake jerk warning.

If the driver does not take action based upon these pro-
gressive warnings, then the system will provide a limited
level of active braking to help slow the vehicle and mitigate
the potential forward collision. If the driver reacts to the
warnings by braking and the system determines that the
driver intends to avoid the collision by braking but has not
applied sufficient brake force, the system will compensate
and provide additional brake force as required.

If a FCW with Mitigation event begins at a speed below
26 mph (42 km/h), the system may provide the maximum
braking possible to mitigate the potential forward collision.
If the Forward Collision Warning with Mitigation event
stops the vehicle completely, the system will hold the
vehicle at standstill for two seconds and then release the
brakes.

210

SAFETY

«
...
210
211
212
213
214
...
»

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

Brand: Jeep Pages: 673

DAF POWERCHOICE 250A

Brand: Paccar Pages: 20

Brand: Kia Pages: 419

Brand: Brodit Pages: 2

Brand: Power Fist Pages: 12

Brand: EAL Pages: 7

StreetLine Series

Brand: SAAS Pages: 4

Brand: GMC Pages: 120

Brand: Prime Tech Pages: 6

Brand: JBL Pages: 12

Brand: BrandMotion Pages: 6

Brand: TOPPOINT Pages: 2

Brand: S&B Filters Pages: 4

Brand: Mazda Pages: 3

Brand: Pet Gear Pages: 4

IGNIS 2022 Series

Brand: Suzuki Pages: 570

Prestige 128-8602

Brand: Audiovox Pages: 8

Brand: Ford Pages: 256

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands