manualshive.com logo in svg

Chrysler pacifica hybrid 2017, Owner'S Manual

The 2017 Chrysler Pacifica Hybrid comes with an informative Owner's Manual that provides detailed instructions and guidelines for maximizing the potential of your vehicle. You can easily download this manual for free from our website, ensuring that you have access to all the information you need to enjoy your Pacifica Hybrid to the fullest.

Share
Download
background image

Engine Malfunction Warning Light

Yellow Telltale

Light

What It Means

Vehicle Check/Malfunction Indicator Light (MIL)

The Vehicle Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System
called OBD II that monitors emissions control systems. The light will illuminate when the igni-
tion is in the ON position before vehicle start up. If the bulb does not come on when placing the
ignition in the ON/RUN position, have the condition checked promptly.
Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the
light after vehicle start. The vehicle should be serviced if the light stays on through several typi-
cal driving styles. In most situations, the vehicle will drive normally and will not require towing.
When the vehicle is running, the MIL may flash to alert serious conditions that could lead to im-
mediate loss of power or severe catalytic converter damage. The vehicle should be serviced as
soon as possible if this occurs.

WARNING!

A malfunctioning catalytic converter, as referenced
above, can reach higher temperatures than in normal
operating conditions. This can cause a fire if you drive
slowly or park over flammable substances such as dry
plants, wood, cardboard, etc. This could result in death
or serious injury to the driver, occupants or others.

CAUTION!

Prolonged driving with the Malfunction Indicator
Light (MIL) on could cause damage to the vehicle
control system. It also could affect fuel economy and
driveability. If the MIL is flashing, severe catalytic
converter damage and power loss will soon occur.
Immediate service is required.

182

GETTING TO KNOW YOUR INSTRUMENT PANEL

Summary of Contents for pacifica hybrid 2017





























































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for pacifica hybrid 2017

JETBAG 320 Fitting Instructions Manual preview
320
Brand: JETBAG Pages: 44
GMC 2005 Sierra Denali Owner'S Manual preview
2005 Sierra Denali
Brand: GMC Pages: 428
Mercedes-Benz GLA 250 2019 Operator'S Manual preview
GLA 250 2019
Brand: Mercedes-Benz Pages: 346
Thule Kit 1514 Instructions preview
Kit 1514
Brand: Thule Pages: 4
Doug Thorley Headers THY-464-1 Instructions preview
THY-464-1
Brand: Doug Thorley Headers Pages: 5
Edelbrock 66002 Installation Instructions preview
66002
Brand: Edelbrock Pages: 2
Würth 071554055 User Instructions preview
071554055
Brand: Würth Pages: 36
Volvo B13R Driver'S Handbook Manual preview
B13R
Brand: Volvo Pages: 24
TATA Motors Sumo Victa EX Owner'S Manual & Service Book preview
Sumo Victa EX
Brand: TATA Motors Pages: 92
ULTIMATE SPEED UAWSO 2 B1 Operation And Safety Notes preview
UAWSO 2 B1
Brand: ULTIMATE SPEED Pages: 32
Chevrolet 1998 Tahoe Manual preview
1998 Tahoe
Brand: Chevrolet Pages: 441
Brink 4698 Fitting Instructions Manual preview
4698
Brand: Brink Pages: 26
Safe Fleet PRIME DESIGN VRR3-FT21G-ST Manual preview
PRIME DESIGN VRR3-FT21G-ST
Brand: Safe Fleet Pages: 12
RAM 2013 2500 Big Horn Information preview
2013 2500 Big Horn
Brand: RAM Pages: 12
FALCON RIDGE CF-UFORCE-DRW01 Instructions For Installation And Care preview
CF-UFORCE-DRW01
Brand: FALCON RIDGE Pages: 6
T.J.M. T13 Outback Frontal Protection System Fitting Instructions Manual preview
T13 Outback Frontal Protection System
Brand: T.J.M. Pages: 18
Audi PXDXVW3 Quick Start Manual preview
PXDXVW3
Brand: Audi Pages: 4
MayPole BC2085 Manual preview
BC2085
Brand: MayPole Pages: 3

Brands by name

Popular brands

Load more brands