Chrysler Pacifica 2021 Owner'S Manual Download Page 66

Page: 66 / 432

GETTING TO KNOW YOUR VEHICLE

UNIVERSAL GARAGE DOOR OPENER

(HOMELINK®)

HomeLink® Buttons And Indicator Light



HomeLink® replaces up to three hand-held

transmitters that operate devices such as

garage door openers, motorized gates,

lighting or home security systems. The Home

Link® unit is powered by your vehicle’s 12

Volt battery.



The HomeLink® buttons that are located in

the overhead console or sunvisor designate

the three different HomeLink® channels.



To operate HomeLink®, push and release

any of the programmed HomeLink® buttons.

These buttons will activate the devices they

are programmed to with each press of the

corresponding HomeLink® button.



The HomeLink® indicator light is located

above the center button.

EFORE

EGIN

ROGRAMMING

OME

INK

For efficient programming and accurate

transmission of the radio-frequency signal, it is

recommended that a new battery be placed in

the hand-held transmitter of the device that is

being programmed to the HomeLink® system.

Make sure your hand-held transmitter is

programmed to activate the device you are

trying to program your HomeLink® button to.
Ensure that your vehicle is parked outside of the

garage before you begin programming.
It is recommended that you erase all the

channels of your HomeLink® before you use it

for the first time.
If you require assistance, please call toll-free

1-800-355-3515 or visit HomeLink.com.

RASING

OME

INK

HANNELS

To erase the channels, follow this procedure:

1. Place the ignition into the ON/RUN

position.

2. Push and hold the two outside HomeLink®

buttons (I and III) for up to 20 seconds, or

until the HomeLink® indicator light flashes.

NOTE:

Erasing all channels should only be performed

when programming HomeLink® for the first

time. Do not erase channels when programming

additional buttons.

DENTIFYING

HETHER

AVE

OLLING

ODE

-R

OLLING

ODE

EVICE

Before programming a device to one of your

HomeLink® buttons, you must determine

whether the device has a rolling code or

non-rolling code.

21_RUP_OM_EN_USC_t.book Page 64

Summary of Contents for Pacifica 2021

















































































































































































































































































































































































































































Search results

Summary of Contents for Pacifica 2021

Reviews:

Chrysler Pacifica 2021, Owner'S Manual, Page: 66 / 432

Search results

Summary of Contents for Pacifica 2021

Reviews: