Chrysler Pacifica 2021 Owner'S Manual Download Page 182

Page: 182 / 432

180

STARTING AND OPERATING

NOTE:

ParkSense will reduce the volume of the radio,

if on, when the system is sounding an audio

tone.

Front Park Assist Audible Alerts
ParkSense will turn off the Front Park Assist

audible alert (chime) after approximately three

seconds when an obstacle has been detected,

the vehicle is stationary, and brake pedal is

applied.

Adjustable Chime Volume Settings
Front and Rear chime volume settings can be

selected from the Uconnect system

page 210.

If the Uconnect system is equipped, chime

volume settings will not be accessible from the

instrument cluster display.
The chime volume settings include LOW,

MEDIUM, and HIGH.
ParkSense will retain its last known

configuration state through ignition cycles.

ARK

ENSE

ARNING

ISPLAY

The ParkSense Warning screen will only be

displayed if “Sound and Display” is selected in

the Uconnect system

page 210.

The ParkSense Warning screen is located within

the instrument cluster display

page 121. It

provides visual warnings to indicate the

distance between the rear fascia/bumper and/

or front fascia/bumper and the detected

obstacle.

WARNING ALERTS FOR FRONT

Front Distance

(inches/cm)

Greater than 47 inches

(120 cm)

47-39 inches

(120-100 cm)

39-25 inches

(100-65 cm)

25-12 inches

(65-30 cm)

Less than 12 inches

(30 cm)

Arcs — Left

None

3rd Flashing

4th Flashing

Arcs — Center

None

1st Solid

2nd Flashing

3rd Flashing

4th Flashing

Arcs — Right

None

3rd Flashing

4th Flashing

Audible Alert Chime

None

Fast

Continuous

Radio Volume Reduced

Yes

21_RUP_OM_EN_USC_t.book Page 180

Summary of Contents for Pacifica 2021

















































































































































































































































































































































































































































Search results

Summary of Contents for Pacifica 2021

Reviews:

Chrysler Pacifica 2021, Owner'S Manual, Page: 182 / 432

Search results

Summary of Contents for Pacifica 2021

Reviews: