manualshive.com logo in svg

Chrysler Pacifica 2021, Owner'S Manual, Page: 141 / 432

Share
Download
Chrysler Pacifica 2021 Owner'S Manual Download Page 141

GETTING TO KNOW YOUR INSTRUMENT PANEL

139

Certain conditions, such as a loose or missing 

gas cap, poor quality fuel, etc., may illuminate 

the light after engine start. The vehicle should 

be serviced if the light stays on through several 

typical driving styles. In most situations, the 

vehicle will drive normally and will not require 

towing.
When the engine is running, the MIL may flash 

to alert serious conditions that could lead to 

immediate loss of power or severe catalytic 

converter damage. The vehicle should be 

serviced by an authorized dealer as soon as 

possible if this occurs.

Service AWD Warning Light — If Equipped

This telltale will turn on to indicate 

that the All Wheel Drive (AWD) system 

is not functioning properly and that 

service is required. Contact an 

authorized dealer.

Service Automatic Emergency Braking 

(AEB) Warning Light — If Equipped

This warning light will illuminate to 

indicate a fault in the AEB Warning 

System. Contact an authorized dealer 

for service  

Ú

page 267.

Service Stop/Start System Warning Light — 

If Equipped

This warning light will illuminate when 

the Stop/Start system is not 

functioning properly and service is 

required. Contact an authorized 

dealer for service  

Ú

page 161.

Tire Pressure Monitoring System (TPMS) 

Warning Light 

The warning light switches on and a 

message is displayed to indicate that 

the tire pressure is lower than the 

recommended value and/or that slow 

pressure loss is occurring. In these cases, 

optimal tire duration and fuel consumption may 

not be guaranteed.
Should one or more tires be in the condition 

mentioned above, the display will show the 

indications corresponding to each tire.

WARNING!

A malfunctioning catalytic converter, as 

referenced above, can reach higher 

temperatures than in normal operating 

conditions. This can cause a fire if you drive 

slowly or park over flammable substances 

such as dry plants, wood, cardboard, etc. This 

could result in death or serious injury to the 

driver, occupants or others.

CAUTION!

Prolonged driving with the Malfunction 

Indicator Light (MIL) on could cause damage 

to the vehicle control system. It also could 

affect fuel economy and driveability. If the 

MIL is flashing, severe catalytic converter 

damage and power loss will soon occur. 

Immediate service is required.

3

21_RUP_OM_EN_USC_t.book  Page 139  

Summary of Contents for Pacifica 2021

















































































































































































































































































































































































































































Reviews:

No comments